|
||
|
|
10th November 2010, 20:47 | #1 |
Gets stuck in
Rover 75 Connoisseur SE CDT Tourer Join Date: Sep 2009
Location: Herne Bay
Posts: 654
Thanks: 1
Thanked 4 Times in 4 Posts
|
Heated seats, how to improve them.
Some may be aware that early this year I decided to have a look at the function of the heated seats, as many including myself were very unhappy at their performance. I discovered a few things about their operation and that of the switch that others may also find useful.
I have to add that I had lots of information from others to help, and I thank Frenchmike, Trebor, Stocktake and others for their help and input. I will give some facts about the standard operation and why the performance is inadequate. Firstly the switch, I spent much time testing and retesting the switch as well as taking the thing apart to try to work it out. The switch appears to be quite a reliable electronic device using various IC's but it definately has an electronic timer in it of about 15 mins or so. But once the timer mechanism has switched the seat off, it will immediately switch the seat heater back on if it is repressed. Secondly, the heated elements have two thermostats in them. One in each element. These thermostats are rated at 40c, but mine and others that have also tested them, they cut out at much less (around 32-34c). Once the temperature has been reached at either part of the seat, one thermostat will cut out and will not reset itself until the seat temperature gets below about 15c. This means in practicable terms that all the time your bottom is on the seat it will not reset. So once 32c or so is reached, the seat will remain at approx 25c or whatever temperature your bottom is. Thirdly, The leather on my seat is thick and it takes about 5 mins for any heat to transfer through the leather to where I can feel it. So, in finding a way of improving the seat, I had to discount anything with the switch, as this is not the real problem. Sure, it might be possible to change one of the microresistors that would extend the timer but the switch is tiny and I do not have the electronic knowledge to do it. Even if this were done it would not stop the thermostats in the elements tripping. So, I started looking around for bi-metalic thermostats that might replace the originals in the element pads. After trying a few, I have now had some positive results from some that I got from Hong Kong. They are 45c(normally closed) thermostats that reset themselves at about 29-30c. The advantage of these thermostats is that the resetting temperature does not require your bottom to leave the seat, and will happily cycle from 30c to 45c permenantly, providing the heated switch is turned back on every 15 mins or so. And you have to remember that 30c is close to the hottest of the current thermostats. So luckily changing the thermostats does not require you to strip the seat cover and can be done relatively easily with either soldered or crimped connectors. The back board does need to be removed, and this is the trickiest part. I would say each seat takes around 30-45 mins and at the end you would feel a definate improvement. How to change the thermostats: So to start with, the backboards need to be removed. Here is a how to by Devilish which I followed http://www.the75andztclub.co.uk/foru...ad.php?t=60562 Although I did unclip the 4 side clips first and then the bottom ones, as I found it easier to be able to see what I was doing with the bottom clips with the sides free. Next step is to unclip the leather from behind the backboard. These are just 3 moulded plastic clips that easily unclip from the metalwork. Once this has been done the clips and the leather just feed between the base and back. Then a little bit of rolling up of the leather on the bolsters will reveal the thermostat. It is under a bit of fabric which needs to be gently prized up. The stat is glued to the element pad and can be prized off very gently or heated up to melt the glue. The old stat needs to be unsoldered and the new one resoldered. I will add at this stage that it would be possible to just solder the wires together and rely on the base stat, but I feel the extra security of 2 stats is worth it as the cost of the stats is so small. The other point is that I think is worth mentioning is that I feel the metal part of the stat should touch the element and not the foam, and not as I had it in my picture. I think this makes it cut out slightly earlier, and we have to remember that the elements will be getting much hotter than before and for longer than before. Next the base stat, which is very easy to get to. If you follow the leather behind the seat you will see three black plastic mouldings attached to the leather. Again these just pull off the metalwork and they and the leather once again feeds up between the seat base and back. This will reveal the base stat, which just needs to replace the existing one. Again my recommendation is to have the metal of the stat touching the element and not the foam. I will add when feeding the leather through between base and back, using the reclining mechanism to a differing position may help. Also when accessing the stats, the seat position may need to be moved to help access. If you wish to test the temperature as a safety check, then on completion a thermometer could be placed between your bottom and the seat and read as the temperature rises and falls. It takes about 10 mins for mine to cut out and maybe another 10 mins for it to automatically start heating again. But your seat should not drop below about 29c. I will add that I have tested my elements to 50c with other stats and they have not failed for me. But my advice is to check that the temperature does not get this high and cuts out somewhere between 40c and 48c. Obviously this modification does carry a risk of damage or failure, and I will not be held responsible for this. I am just describing what I have done to my car and why. Hope this is of some help, as I say about 45 mins work for each seat and then considerably hotter seats. Sit back and enjoy. Matt Photos of: Back of seat without backboard showing leather to be fed up between back and base. Old thermostat. New thermostat soldered on (but stat needs to be upside down and not as in photo). Last edited by Dragrad; 16th December 2012 at 21:42.. |
10th November 2010, 20:54 | #2 |
RS South East
Ford fester... blah.... Join Date: Mar 2010
Location: Hastings
Posts: 2,900
Thanks: 29
Thanked 78 Times in 42 Posts
|
great work matt, mine barely get warm never mind hot and i've got the leather seats. Any idea of cost and source for the parts?
I did ask if Paul (Rastlin) had concidered switching on the seats with his remote FBH project, think he missed my query though - any thoughts?
__________________
the name's Bernard but you can call me nursie...... |
10th November 2010, 21:08 | #3 |
This is my second home
2005 Connoisseur SE 1.8 Turbo,2004 45 1.8 Connoisseur and my beloved 1998 VVC Coupe. Join Date: Nov 2009
Location: Derby.
Posts: 8,790
Thanks: 2,022
Thanked 1,016 Times in 739 Posts
|
Great bit of research,and i agree with all your comments on the OEM set up.
__________________
|
10th November 2010, 21:08 | #4 |
Avid contributor
Rover 75 CDT Join Date: Nov 2006
Location: Northampton
Posts: 217
Thanks: 6
Thanked 9 Times in 6 Posts
|
The sooner as I switch mine on I feel them then they go straight off, this would be worthwhile.
|
10th November 2010, 21:08 | #5 | |
Gets stuck in
Rover 75 Connoisseur SE CDT Tourer Join Date: Sep 2009
Location: Herne Bay
Posts: 654
Thanks: 1
Thanked 4 Times in 4 Posts
|
Quote:
http://cgi.ebay.co.uk/2x-KSD-301-Tem...item27b120fcaa I am not sure that switching on remotely would be of any real benefit unless you left something of weight on the seat to facilitate the heat transfer through the leather. The elements themselves heat up in a very short time. Matt |
|
10th November 2010, 22:58 | #6 |
This is my second home
75 Contemporary SE Mk II 2004 Man. Sal. CDTi 135ps, FBH on red diesel, WinCE6 DD Join Date: May 2010
Location: Leeds
Posts: 17,273
Thanks: 2,160
Thanked 2,061 Times in 1,586 Posts
|
There is also the likelihood of the battery suffering a quite considerable discharge if the engine is not running with the seats turned on.
__________________
Harry How To's and items I offer for free, or just to cover the cost of my expenses... http://www.the75andztclub.co.uk/foru...40#post1764540 Fix a poor handbrake; DIY ABS diagnostic unit; Loan of the spanner needed to change the CDT belts; free OBD diagnostics +MAF; Correct Bosch MAF cheap; DVB-T install in an ex-hi-line system; DD install with a HK amp; FBH servicing. I've taken a vow of poverty. To annoy me, send money. |
11th November 2010, 06:04 | #7 |
Vis Whiz
Rover 75 2.5 auto Saloon Join Date: Jun 2007
Location: LEEDS
Posts: 20,593
Thanks: 2,057
Thanked 3,056 Times in 1,621 Posts
|
Just ordered mine Matt, looking forward to the how to
__________________
Dave... Lost a few stones and a Gall Bladder and part of a bile duct and all of my dignity in the suppository incident |
11th November 2010, 06:05 | #8 |
I really should get out more.......
BMW I3 Join Date: Nov 2006
Location: South East London
Posts: 2,224
Thanks: 31
Thanked 77 Times in 61 Posts
|
Great Matt, would be nice to see a picture of the units installed, just for the num nums like me to see how they are fitted
__________________
Regards Tony Membership No 135 |
11th November 2010, 10:49 | #9 |
I really should get out more.......
260 SE vin 214 ( last mark 1 260 ) Join Date: Dec 2006
Location: Lancashire
Posts: 2,009
Thanks: 1
Thanked 8 Times in 4 Posts
|
good work- pics would be nice, the 260 does need the seats improving- they are very cold in winter, and even on full chat, the heater cannot be described as toasty
__________________
[SIGPIC][/SIGPIC] |
11th November 2010, 12:41 | #10 |
Banned
75 CDT Connoisseur SE Auto Join Date: Nov 2006
Location: Wolverhampton
Posts: 8,450
Thanks: 0
Thanked 3 Times in 3 Posts
|
|
|
|