|
||
|
|
2nd October 2010, 15:03 | #1 |
Avid contributor
MG ZT Join Date: Dec 2006
Location: The Netherlands
Posts: 137
Thanks: 0
Thanked 0 Times in 0 Posts
|
Installing the RadioGuy Double Din
Hi guys.
Got mine in yesterday and started installing today what a weekend present Ill give a short description to what was originally fitted and where i routed the cables and stuff. The car MG ZT 190 2003 V6 Petrol. Fitted Harmon Kardon Speakers with the sub. Headunit Alpine Syphony? anyways the one without navigation. Kenwood 6 cd changer. Before you start anything with this config FIRST REMOVE ALL THE CD's From your cd Changer. First step Remove the old Headunit.
Remove the Kenwood cd changer from the glovebox Yaay i finally i will be able to use the glovebox for more then 1 sheet of paper.
I found removing the glovebox gave great acces to the passenger side under the dash and this is where i decided to route all the aireals.
Now the fun part putting cables in. I routed the GPS from the A-Pylar on my passenger side down though a small gap in the plastic then the connector was fed alongside the fuse box towards the center console and fed though the hole where the Old CD Changer cable was routed. The Block part on the gps antenna i fitted about 2 inches from the windscreen and 1 inch from the side of the a-pylar. The cable i could hide in between the plastic of the dash and the stuff that covers the A Pylar. Now here's where i'm a bit lost. I was delivered an extra areal in my kit for i think TMC and since i noticed 2 arial connections on the back of the unit i figured i should use them both. One areal connector has the discription ANT next to it and can be seen in sean's pictures the other one is a Cable that comes out of the back of the unit Black with a Female Antenna connector. (figure this is the TMC areal) So the one that was delivered extra i the same way but instead of going forward i moved along the door rubber upwards towards the roof. I found i could hide the cable since its so small underneath the ruber liner all the way to the back of the car. Now the fun part and the part i think i made a mistake. So i plugged everything in the 2 iso blocks no problems then the 3 little combo plugs Blue Green Yellow. (on my original setup only the Blue one was used and was for all the Kenwood cd changer) This is now the Ipod cable. So i hooked everything up and 3 things don't work correctly. 1 the Steering wheel controls I probablly need to connect 2 wires from the iso block to something else ? 2 The Areal amp is not getting power because my radio reception went to the dogs. Probablly need to wire it up somewhere? 3 TMC is found but can't find a station to lock on for TMC data. I know there are stations that serve TMC data it won't lock on. Thats how far i got then i lost track between all the colors of wires and i had to put an ipod on the unit and testout the sound. Yes it's GOOD. Then to test out the navigation Locks on to your pos verry quickly so the position of the GPS areal is good. Then pop in the matrix dvd and see hear and Feel them shooting eachother so nice. So i'm hoping somebody can point me in some direction to get these last issues fixed. Since i have no more time to spend on it i've put everything in and put back the glovebox the headunit is in place and ill work on it when i have some more info. Regards Prom
__________________
Car info. MG ZT 190 2003 |
2nd October 2010, 15:44 | #2 |
Newbie
mg zt 190 Join Date: Sep 2010
Location: Berlicum NL
Posts: 21
Thanks: 0
Thanked 0 Times in 0 Posts
|
It worked and now it doesn't
Installed the new unit and it worked fine for about 20 minutes.
I left the cd player on and went into the house to get some lunch. When I came back the screen was dead. I started up again , but didn,t work out. the icons on my dash flickered and the car wouldn't start anymore. Pulled the unit out,disconnected it and still the car won't start. I disconnected the battery and went to my computer. Here I am. I have checked the connections on the Iso bloc off my car. The yellow is not wired and the green has 2 wires, one on 3 and one on 1. The radio I pulled out worked fine on these. Anyone the solution to this huge problem.?? regards, Kees |
2nd October 2010, 19:04 | #3 | |
This is my second home
MG ZT260 SE, MG ZT190+, MG ZTT 160, R75 Conn SE 2.0, R75 Conn SE 2.5 X 3, R75 Club SE 1.8, P5B Coupe Join Date: Jul 2009
Location: Keynsham, Bristol
Posts: 4,211
Thanks: 65
Thanked 635 Times in 499 Posts
|
Quote:
|
|
2nd October 2010, 19:24 | #4 |
This is my second home
Back in a Rover Join Date: Nov 2006
Location: Peterborough
Posts: 4,926
Thanks: 131
Thanked 357 Times in 261 Posts
|
These chinese units do take a lot of power I know JakeW has flattened his battery showing members at meets it's functions.
Stubs |
2nd October 2010, 19:40 | #5 |
Banned
2004 75 Contemporary SE Tourer, 2005 (55) Pearl Black Conn. SE Tourer. Join Date: Jul 2009
Location: Lincoln
Posts: 2,129
Thanks: 0
Thanked 0 Times in 0 Posts
|
|
2nd October 2010, 20:32 | #6 |
Newbie
mg zt 190 Join Date: Sep 2010
Location: Berlicum NL
Posts: 21
Thanks: 0
Thanked 0 Times in 0 Posts
|
|
2nd October 2010, 20:43 | #7 |
Gets stuck in
ROVER 75 2.0 CD DIESEL Join Date: Jun 2009
Location: Barnsley
Posts: 906
Thanks: 0
Thanked 1 Time in 1 Post
|
It may not even be flat, it could just be that the connection is loose...
It happens on mine sometimes !
__________________
Mark - " Maximum Planning - Minimum Mistakes !! "
*** NO TMC MOD KITS AVAILABLE !! *** See the TMC / RADIO VIDEOS HERE.... Send me an Email HERE…. Signup for Sugarsync HERE.. http://sincemylastcigarette.com/bann...GBP_5_dark.png |
3rd October 2010, 12:23 | #8 | |
Banned
None Join Date: Feb 2010
Location: Here on the Forum
Posts: 5,352
Thanks: 632
Thanked 822 Times in 573 Posts
|
Hi Prometheus
Thank you for the stepp by Step, In answer to your questions: Quote:
|
|
4th October 2010, 06:53 | #9 |
Avid contributor
MG ZT Join Date: Dec 2006
Location: The Netherlands
Posts: 137
Thanks: 0
Thanked 0 Times in 0 Posts
|
Ill take some pictures this afternoon and post them in this thread to let you guys see where and how i routed stuff. (The easy part) Hooking it up to the existing loom (the hard part) ill ask the questions here
__________________
Car info. MG ZT 190 2003 |
3rd October 2010, 15:02 | #10 |
Newbie
mg zt 190 Join Date: Sep 2010
Location: Berlicum NL
Posts: 21
Thanks: 0
Thanked 0 Times in 0 Posts
|
the mgzt roars again
Eh,,, The battery was flat.
This far the radio works, the cdplayer works with my mp3 cd,the gps works I got my coordinates. Navigation not tested yet. Steeringwheel controls I have to wire I presume; how? When I shut off the car the wipers make a wipe;??. they didn't before. A lot off playing and testing to do. No manual received for the Igo, is there one? For the people who cab help me with the wiring: My yellow block is not wired, the green block is wired on 3 with purple/blue and on 1 with orange/green, that's all. regards, Kees |
|
|