|
||
|
14th June 2018, 18:46 | #1 |
Regular poster
Rover 75 Club SE + R75 Tourer Club Join Date: Nov 2014
Location: Worcester
Posts: 81
Thanks: 4
Thanked 1 Time in 1 Post
|
Clutch Problems
This R75 i've bought really is trouble......... The clutch on this car has never felt right, despite the fact that the previous owner has had the DMF changed 10k miles ago, and a new clutch kit, slave cylinder and master cylinder fitted in the last 500 miles! Today, the biting point was all over the place, and gears were hard to select. I'm guessing the slave cylinder has failed already. What do you all think? The pedal also feels really spongey.
|
14th June 2018, 19:36 | #2 |
Gets stuck in
75 saloon 2.0 diesel Join Date: Feb 2016
Location: Panton, lugo, Galicia
Posts: 945
Thanks: 236
Thanked 192 Times in 143 Posts
|
Bleed it
|
16th June 2018, 13:11 | #3 |
Newbie
75 tourer Join Date: Oct 2011
Location: Lincoln
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Same problem developed on my Tourer (110 k miles) which I bought a few weeks ago. It turned out to be a slight fluid weep at the clutch master cylinder; At first I suspected major clutch / DMF problems but when I just couldn't select a gear I found the fluid was empty. I have a new one ready to change along with replacing the clutch and slave (just in case)
Keeping the problem at bay until I have time to change it all by topping up the master cyl every couple of weeks. What a STUPID location for that master cyl !!! Using a plastic pipette to add a teaspoonful at a time once I have struggled with getting to it and got the cap off - no other way I can see. Sure does exercise the Anglo-Saxon vocabulary ! For interest I am replacing the DMF with a solid flywheel and will report back when done Last edited by Derek Oliver; 16th June 2018 at 13:19.. Reason: Expanded detail |
16th June 2018, 13:25 | #4 |
Gets stuck in
75 saloon 2.0 diesel Join Date: Feb 2016
Location: Panton, lugo, Galicia
Posts: 945
Thanks: 236
Thanked 192 Times in 143 Posts
|
Bleed it first.
|
16th June 2018, 13:32 | #5 |
This is my second home
Rover 75 tourer Club CD/Limo Tints Join Date: Nov 2008
Location: Meneac
Posts: 6,759
Thanks: 5,007
Thanked 1,609 Times in 869 Posts
|
Dmf
For interest I am replacing the DMF with a solid flywheel and will report back when done.
It has a DMF for a reason,Have a good read on here about DMF V Solid Fly Wheel.....Makes for interesting reading
__________________
] "I started out with nothing, and Ive still got most of it left!" |
19th June 2018, 17:59 | #6 |
Regular poster
Rover 75 Club SE + R75 Tourer Club Join Date: Nov 2014
Location: Worcester
Posts: 81
Thanks: 4
Thanked 1 Time in 1 Post
|
It turns out the master cylinder (new supposedly!) is leaking badly. There's fluid all over the footwell! I think it's a combination of a poor quality part, and very bad fitment. In the mean time, I have ordered a Tazu replacement, and I'll tackle the job myself this weekend.
Out of interest, is there anything to fear with the Tazu replacement parts? They seem better quality than most I have seen, but I have seen reports of seal failure on earlier production runs. |
19th June 2018, 18:44 | #7 | |
Gets stuck in
75 saloon 2.0 diesel Join Date: Feb 2016
Location: Panton, lugo, Galicia
Posts: 945
Thanks: 236
Thanked 192 Times in 143 Posts
|
Quote:
Where is it leaking from? Is it at the pipe? Is the plastic cap on tight? You'll get plenty of differing opinions on the Tazu stuff but I found it be OK. Do you know what brand was fitted? There was a duff batch of slave cylinders a while back where no / insufficient grease was applied. The mk2 tazu master was a disaster and pulled from production. I think I'm right in saying that the tazu stuff has been adopted by xpart??? Check out dmgrs site. |
|
19th June 2018, 19:43 | #8 |
This is my second home
Rover 75 tourer Club CD/Limo Tints Join Date: Nov 2008
Location: Meneac
Posts: 6,759
Thanks: 5,007
Thanked 1,609 Times in 869 Posts
|
Tazu
I have had a Tazu Mk1 master fitted,done 50k with it and as yet no problems
__________________
] "I started out with nothing, and Ive still got most of it left!" |
19th June 2018, 20:35 | #9 | |
This is my second home
Rover 75 Saloon & Tourer Join Date: Sep 2012
Location: Lincoln
Posts: 14,928
Thanks: 1,630
Thanked 3,032 Times in 2,181 Posts
|
Quote:
the advice on this forum is not to use a solid flywheel macafee2 |
|
23rd June 2018, 18:02 | #10 |
Regular poster
Rover 75 Club SE + R75 Tourer Club Join Date: Nov 2014
Location: Worcester
Posts: 81
Thanks: 4
Thanked 1 Time in 1 Post
|
Clutch operation has been restored, thanks to a Tazu replacement master cylinder! It wasn't as bad a job as I had anticipated thankfully. One side effect of the kit seems to be a noticably heavier clutch over an OEM part, presumably due to the narrow bore of the copper pipe supplied with it. If anyone else is tackling this job, then please be aware of it.
|
|
|