|
||
|
29th May 2018, 14:20 | #21 |
MG ZT Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
|
Here is a contact Denis, I used a small telescopic aerial to make an extraction tool Basically the two tangs need to be depressed simultaneously and the contact pushed out Brian |
29th May 2018, 17:38 | #22 |
Loves to post
MG-ZT190 Join Date: Oct 2015
Location: Kopeysk Town
Posts: 413
Thanks: 144
Thanked 9 Times in 9 Posts
|
|
29th May 2018, 21:08 | #23 |
I really should get out more.......
P6B, L550, Imp, F56, Commando Join Date: Nov 2006
Location: Aberdeenshire
Posts: 2,886
Thanks: 352
Thanked 677 Times in 440 Posts
|
and here was me scrabbling about the other night with my grey connector trying to find a way to remove the contact pins to find the values of the resistors for Denis as everything is a bit squashed up in there. In the end I gave up and saw you had posted the wiring diagram anyway. However the idea of the aerial is a good one for the future to try.
|
30th May 2018, 03:12 | #24 | |
Loves to post
MG-ZT190 Join Date: Oct 2015
Location: Kopeysk Town
Posts: 413
Thanks: 144
Thanked 9 Times in 9 Posts
|
Quote:
Please tell me what is the accuracy of T4 determines the cable's resistance? Regards Denis |
|
30th May 2018, 13:51 | #25 |
Loves to post
MG-ZT190 Join Date: Oct 2015
Location: Kopeysk Town
Posts: 413
Thanks: 144
Thanked 9 Times in 9 Posts
|
At me resistance of 500 Ohm on the device shows 469 Ohm. Is it not critical?
Regards Denis |
31st May 2018, 01:06 | #26 |
Loves to post
MG-ZT190 Join Date: Oct 2015
Location: Kopeysk Town
Posts: 413
Thanks: 144
Thanked 9 Times in 9 Posts
|
Hello.
Tell me please. Regards Denis |
1st June 2018, 07:35 | #27 |
Loves to post
MG-ZT190 Join Date: Oct 2015
Location: Kopeysk Town
Posts: 413
Thanks: 144
Thanked 9 Times in 9 Posts
|
|
1st June 2018, 07:51 | #28 |
I really should get out more.......
P6B, L550, Imp, F56, Commando Join Date: Nov 2006
Location: Aberdeenshire
Posts: 2,886
Thanks: 352
Thanked 677 Times in 440 Posts
|
I cannot say for sure how accurate the resistance reading need to be to fool T4 into thinking the correct connector has been fitted. However if you have the cable patch dapd0002.exe installed then in theory T4 should let you progress through this stage of the grey connector request with an out of tolerance resistance
|
1st June 2018, 08:00 | #29 | |
Loves to post
MG-ZT190 Join Date: Oct 2015
Location: Kopeysk Town
Posts: 413
Thanks: 144
Thanked 9 Times in 9 Posts
|
Quote:
Patch dapd0002.exe I have. If T4 does not miss the gray cord will install the patch. Still, I would like to know with what accuracy T4 defines cables. Regards Denis |
|
1st June 2018, 11:23 | #30 |
MG ZT Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
|
|
|
|