|
||
|
26th February 2011, 22:35 | #1 |
Avid contributor
MG ZT 1.8T & CDTI 135 Join Date: May 2010
Location: SOUTH COAST
Posts: 201
Thanks: 11
Thanked 13 Times in 12 Posts
|
Finally fixed my misfire at long last!!!
Hi guys you may or may not know I have been having problems with my car since oct/nov and it's only today that I have actually fixed the problem.
Apologies for the essay but maybe this will help someone else in the future. It started back in October when my car started behaving badly with the cold weather etc; Steamy exhausts and check engine lights, lumpy running, stuttering, coughing, jerking, surging, etc. It then got progressively worse and started to misfire alot especially under hard acceleration.... 1st off I replaced the spark plugs from NGK platinums to NGK V-Grooves as this was all I could afford at the time and there was a noticeable difference in smoothness. But the car was still not right.... I then replaced the coilpacks which made no difference.... So I though OK I'll replace the HT Leads- again no improvement either. I was pretty sure it wasn't the turbo vacuum pipes as I had previously replaced them with petrol pipe... But anyway just to be sure they hadnt started leaking I bought some new silicone tubing and replaced all 3.... But as suspected no improvement again! So in the few months I spent wondering WTF is wrong with this Bl***y thing I bought a VVC inlet manifold to swap over as I thought maybe there is a crack that is opening up under load... It had a few sensors on it so I took the throttle position sensor off to try a swap with mine and again this did nothing, except maybe idle slightly lumpier. I havent got round to swapping the manifolds over yet.... So as time went on the exhaust has developed a rather deep noise as I think the baffle has gone or is going maybe related to all the misfiring, so my next thought was some bits of metal floating about and causing a blockage in the exhaust at high revs.... So I started contemplating a new back box which I cant really afford an OEM one and dont want a cheap noisy stainless one. I also thought maybe the fuel pump had began to pack up or I was experiencing FFS. So I checked the fuel filter and it was fully tight so that was a relief... All this time I had been researching the causes of misfires under acceleration and there are loads of reasons why it could happen! Next thought was lambda sensors, Inlet manifold gasket, cam sensor, leaky throttle body, catalytic covertor,etc. - The expensive stuff Anyway turns out the spark plugs I fitted were gapped to 1.0mm +/- 0.05mm as recommended. After my extensive research I thought I'll just try reducing the gap as it cant hurt to give it a go and it costs nothing! So I regapped the spark plugs to around 0.5mm earlier today and guess what the misfire has gone completely!!! So glad I didn't spend anymore money on things that didnt need replacing!!! I love my car again and might even give it a clean 2moro |
27th February 2011, 07:51 | #2 |
Loves to post
Rover 75 1.8T 2003 Club SE Join Date: Jan 2009
Location: Solihull,
Posts: 370
Thanks: 0
Thanked 0 Times in 0 Posts
|
That .5mm equates to 20thousands of an inch in old money which sounds about right. Most cars use about 25 thou. The 1.0mm was too big.
JCW |
27th February 2011, 08:40 | #3 |
Ex Owner
MX-5 ND2 RF Join Date: Sep 2010
Location: Leigh
Posts: 6,574
Thanks: 462
Thanked 799 Times in 524 Posts
|
Very pleased you've solved it, must store this information away for future reference.
It's surprising that a lot of potentially expensive problems turn out to be the simplest of solutions. |
27th February 2011, 09:09 | #4 |
Banned
MG ZT V6 190+ Join Date: Sep 2008
Location: Leeds
Posts: 33,223
Thanks: 41
Thanked 1,614 Times in 1,416 Posts
|
starting to read your post when you mentioned a steamy exhaust and a miss fire i thought inlet manifold gasket..anyway the MIL light is very sensitive to a miss fire and the cheapest option is the spark plugs.
glad to hear your sorted. |
5th April 2011, 20:23 | #5 |
Newbie
Rover 75 Contempory SE Join Date: Feb 2011
Location: Devon
Posts: 16
Thanks: 2
Thanked 0 Times in 0 Posts
|
Sounds interesting, I have had a misfire on my 1.8 T now for around 2 months, changed coil packs, MAP sensor and plugs but to no avail, I will try the plug gap, it is in the garage at present as they are scratching their heads as what to do next, see my thread ' Engine misfire '
|
9th April 2011, 20:56 | #6 | |
Avid contributor
MG ZT-T Join Date: Feb 2011
Location: CHESTER
Posts: 211
Thanks: 0
Thanked 0 Times in 0 Posts
|
Quote:
We have both seen your thread and put the same answer on it back then. Gaz |
|
17th April 2011, 07:28 | #7 |
Regular poster
MG ZT (2001) Join Date: Feb 2011
Location: Barnstaple. North Devon
Posts: 52
Thanks: 0
Thanked 0 Times in 0 Posts
|
I missed this post as mine has also had this problem, had new plugs, then coils packs, then had the exhaust done, and lambda sensors. now going out today to check my gaps to see if the garage did the right gap, please please, please let this be my problem
|
17th April 2011, 10:52 | #8 | |
Regular poster
MG ZT (2001) Join Date: Feb 2011
Location: Barnstaple. North Devon
Posts: 52
Thanks: 0
Thanked 0 Times in 0 Posts
|
Quote:
Well spark plugs now done (they were all well over 1mm and now all down to .5 mm, and this was a garage doing the plugs) and heres the moment of truth, will let you know in about half hour or so. (Touch Wood) |
|
17th April 2011, 11:16 | #9 |
Regular poster
MG ZT (2001) Join Date: Feb 2011
Location: Barnstaple. North Devon
Posts: 52
Thanks: 0
Thanked 0 Times in 0 Posts
|
OMG, I now love my car again.
After everything I have done to get rid of this mis fire feeling and it looks like it was just the spark plug gap. (Never going to get a garage to do it again) Yaaaaaaaahhayyyyyyyyyyyyyyyy Praise be to this site |
18th April 2011, 09:20 | #10 |
Avid contributor
Rover 75 Join Date: Nov 2010
Location: Slovenia
Posts: 157
Thanks: 0
Thanked 2 Times in 2 Posts
|
How can i check on my car that? I also changed plugs,leads,coils,cam sensor and still it doesnt pull like it shoud? How can i regap my plug's to 0.5mm?
|
|
|