|
||
|
22nd February 2009, 15:22 | #1 |
Posted a thing or two
75 Conn S.E. Cdt. Join Date: May 2007
Location: Merseyside
Posts: 1,803
Thanks: 1,873
Thanked 52 Times in 49 Posts
|
Injector.
I have just replaced my PCV and everything was going great until I broke the piece of plastic which pushes into the n/s injector and is connected to fuel return pipe. Can I buy the small piece or is it a new injctor?. Thanks.
|
22nd February 2009, 15:53 | #2 |
This is my second home
Waiter, Waiter! I seem to have a Roomster in my drive... Join Date: Nov 2006
Location: Sussex
Posts: 3,268
Thanks: 0
Thanked 1 Time in 1 Post
|
if its a t-piece I think you can get the full return pipe kit with those and new o-rings from bmw, no doubt xpart too.
|
22nd February 2009, 16:03 | #3 |
Posted a thing or two
75 Conn S.E. Cdt. Join Date: May 2007
Location: Merseyside
Posts: 1,803
Thanks: 1,873
Thanked 52 Times in 49 Posts
|
Injector.
Thanks Pondweed, the piece is not a tee piece it is the end one with just an inlet but no outlet. Can I just go to a motor factor or a taxi garage or is it BMW as I need the car so need to pick the part(s) up tomorrow?. Thanks again.
|
22nd February 2009, 18:24 | #4 |
Been absent for a while…
Rover 75 Tourer, Classic mini Cooper S, Abarth 595 competizione, MG TF and a Hyundai Tucson PHEV Join Date: Feb 2007
Location: Cumbria
Posts: 13,065
Thanks: 1,033
Thanked 1,686 Times in 1,040 Posts
|
Not sure about the Rovers but you usually have to buy the full leak off pipe for all injectors. somebody with EPC might be able to advise better
__________________
................................................. 'Marmite' Possibly one of the most famous 75 tourers produced! left the production line as the last of only Three Rover 75 tourers produced in Trophy Yellow. 48 hours later Longbridge closed. The last sold ordered 75 Tourer. Paid for by the Phoenix Four and handed over by John Towers to the Warwickshire Northampton Air ambulance service as a Rapid Response vehicle |
22nd February 2009, 18:50 | #5 |
Posted a thing or two
75 Conn S.E. Cdt. Join Date: May 2007
Location: Merseyside
Posts: 1,803
Thanks: 1,873
Thanked 52 Times in 49 Posts
|
Injector.
Thanks Sworks, I will phone BMW tomorrow.
|
24th February 2009, 15:30 | #6 |
Posted a thing or two
75 Conn S.E. Cdt. Join Date: May 2007
Location: Merseyside
Posts: 1,803
Thanks: 1,873
Thanked 52 Times in 49 Posts
|
Injector.
I ordered from Rimmers lunch time yesterday and it arrived 9a.m.today. The kit cost £23. I only needed the very end bit that clips into the injector so will keep the rest as spares. Well done to Rimmers.
|
24th February 2009, 21:20 | #7 |
This is my second home
None * DROWNED Join Date: Aug 2007
Location: Cardigan
Posts: 33,339
Thanks: 1,257
Thanked 1,664 Times in 1,081 Posts
|
Could you please post the part number for others to take note (esp me, as I will attempt to do the same, change the PCV that is)
__________________
Andrew Ich Dien Problem solving is... lateral thinking SEARCH FIRST ...ASK LATER... |
25th February 2009, 05:52 | #8 |
Posted a thing or two
75 Conn S.E. Cdt. Join Date: May 2007
Location: Merseyside
Posts: 1,803
Thanks: 1,873
Thanked 52 Times in 49 Posts
|
Injector.
Here is the part no. for the fuel return pipe= MSP101341. HTH.
|
2nd March 2009, 00:34 | #9 |
This is my second home
None * DROWNED Join Date: Aug 2007
Location: Cardigan
Posts: 33,339
Thanks: 1,257
Thanked 1,664 Times in 1,081 Posts
|
Changed the PCV filter and housing on Sunday... No problem
__________________
Andrew Ich Dien Problem solving is... lateral thinking SEARCH FIRST ...ASK LATER... |
|
|