|
||
|
17th August 2017, 09:50 | #1 |
Regular poster
zt 260 se and zt-t190 Join Date: Sep 2009
Location: huddersfield
Posts: 67
Thanks: 4
Thanked 0 Times in 0 Posts
|
heated seat wiring
hi
I'm fitting replacement heated,electric leather seats to my 55 plate ZTT 190 + my question is that although the wiring looms are already in place for the seats to plug into I cant seem to find the plugs for the heated seat swiches behind the facia panel. I just presumed that if the seat looms were already there then the heated seat switch plugs would be present too. any help greatly appreciated thanks |
17th August 2017, 10:00 | #2 |
SERVICING AND DEALER DIAGNOSTICS
MG ZT CDTI 135 + & MGZT CDTI AUTO 160 & ROVER 75 TOURER CDTI 160 TROPHY YELLOW Join Date: Aug 2013
Location: Hernebay
Posts: 4,331
Thanks: 818
Thanked 2,414 Times in 1,141 Posts
|
Remove the air con panel and they will probably be wrapped up behind it,
Mick
__________________
[SIGPIC][/SIGPIC] T4 Owner Jobs done : new UBP, Spy hole mod, Rear hub(wheel bearing),plenum cleaned and emptied, Inline thermostat fitted,Full service, In car Digital tv/DVD Bluetooth Satnav etc, Replaced UBP, Restored headlights,Fixed airbag connection.replaced HP pump,replaced rear light seals,changed intercooler O rings. Jobs to do: ,replace drivers lock,.[/SIZE] |
17th August 2017, 10:03 | #3 |
Regular poster
zt 260 se and zt-t190 Join Date: Sep 2009
Location: huddersfield
Posts: 67
Thanks: 4
Thanked 0 Times in 0 Posts
|
done that pal cant see owt
|
17th August 2017, 11:02 | #4 |
Loves to post
MG ZT Join Date: Sep 2015
Location: Dunmow
Posts: 350
Thanks: 139
Thanked 83 Times in 72 Posts
|
Heated seat switch wiring
I'm about to fit heated seats to my Mk1 ZT and found the wiring loom for the switches very easily. After removing the switch fascia plate the seat switch connectors were bundled together wrapped in sticky tape together with the connector for the rear blind switch and all three were lodged in the slot where the blind switch usually goes. The seat looms were even helpfully labelled as to which was left and right! They are together quite a substantial bit of wiring so if you can't see them, the likelihood is that they're not there. Do you have cruise control? I do and have been told that if the factory was fitting wiring for one item in the lower switch panel then they fitted all of them, even though only one was being used.
|
17th August 2017, 12:57 | #5 |
Regular poster
zt 260 se and zt-t190 Join Date: Sep 2009
Location: huddersfield
Posts: 67
Thanks: 4
Thanked 0 Times in 0 Posts
|
hi
no cruise fitted,going to have another good look but don't think its there,got a/c panel and radio out and cant see nowt,just my luck |
17th August 2017, 13:46 | #6 |
SERVICING AND DEALER DIAGNOSTICS
MG ZT CDTI 135 + & MGZT CDTI AUTO 160 & ROVER 75 TOURER CDTI 160 TROPHY YELLOW Join Date: Aug 2013
Location: Hernebay
Posts: 4,331
Thanks: 818
Thanked 2,414 Times in 1,141 Posts
|
I have on the odd occasion found them up behind where the stereo is fitted whilst dismantling,
Mick
__________________
[SIGPIC][/SIGPIC] T4 Owner Jobs done : new UBP, Spy hole mod, Rear hub(wheel bearing),plenum cleaned and emptied, Inline thermostat fitted,Full service, In car Digital tv/DVD Bluetooth Satnav etc, Replaced UBP, Restored headlights,Fixed airbag connection.replaced HP pump,replaced rear light seals,changed intercooler O rings. Jobs to do: ,replace drivers lock,.[/SIZE] |
17th August 2017, 17:26 | #7 |
I really should get out more.......
A Reasonably Priced Car Join Date: Jan 2014
Location: Burton Latimer
Posts: 2,530
Thanks: 408
Thanked 1,064 Times in 712 Posts
|
Another hiding place for these connectors is - behind the ash tray area inside the console, you will be looking for a grey coloured foam end with a few cables entering it. You may need to unclip the ashtray/cupholder section to enable a good search for them.
|
Thread Tools | |
Display Modes | |
|
|