|
||
|
5th November 2019, 10:06 | #1 |
This is my second home
ZT260 #243 (resting) Join Date: May 2010
Location: Prestonpans
Posts: 22,486
Thanks: 650
Thanked 4,624 Times in 3,358 Posts
|
Any plumbers here?
I have an "old" cold water system with a storage tank in the loft. The overflow started dribbling a good while ago so I replaced the diaphragm in the float valve and it has been fine for a couple of years but its not shutting off fully again. Replaced the diaphragm but it made no difference I was going to replace the float valve itself but its located at the rear of the tank and the inlet pipe to valve connection is all but inaccessible.
Any suggestions why a new diaphragm hasn't cured it? |
5th November 2019, 10:17 | #2 | |
This is my second home
Roverless + 1.7D Sportage Join Date: Aug 2014
Location: East Norfolk
Posts: 7,050
Thanks: 729
Thanked 2,021 Times in 1,449 Posts
|
Quote:
__________________
Oil in my veins! |
|
5th November 2019, 10:42 | #3 |
This is my second home
ZT260 #243 (resting) Join Date: May 2010
Location: Prestonpans
Posts: 22,486
Thanks: 650
Thanked 4,624 Times in 3,358 Posts
|
Pressure hasn't changed, not noticeably. The arm is bent anyway, dumb set up, the valve is above the level of the overflow. I suspect I'm going to have to find some way of getting access to the rear of the tank and replace the whole valve, its at a low section of the roof, no "flooring", need to crawl into position then try to balance myself crouched down on the rafters! Recipe for disaster!
|
5th November 2019, 14:12 | #4 |
This is my second home
Rovers 75 & 25 Join Date: Oct 2010
Location: Wearside
Posts: 4,522
Thanks: 543
Thanked 709 Times in 511 Posts
|
We once had a loft tank with a ball valve and there came a time when changing the rubber washer did not fix the problem entirely because the seat of the valve it sealed against deteriorated with age too. We changed the valve and all was well but we eventually opted to replace the system with a new one and a combi boiler. Given what you have said about access and maybe your health and age previously Steve it might be worth considering getting someone in to do the job for you. I find myself doing this more often as time goes by because where the mind is still willing the body often protests quite strongly - and for quite a while after when I get it wrong.
|
5th November 2019, 15:08 | #5 |
Precise
Rover 75 Tourer 2.5KV6 Connoisseur SE Join Date: Mar 2013
Location: Fleet
Posts: 2,954
Thanks: 630
Thanked 617 Times in 480 Posts
|
If you can see the rafters (do you really mean ceiling joists?) you have not got enough insulation!!
|
5th November 2019, 15:49 | #6 | |
This is my second home
ZT260 #243 (resting) Join Date: May 2010
Location: Prestonpans
Posts: 22,486
Thanks: 650
Thanked 4,624 Times in 3,358 Posts
|
Quote:
No, I can't see the joists but I know there's no flooring in that area. When we inherited the place from my parents there was only a small floored area in the middle of the loft but I increased the size for more storage space. |
|
5th November 2019, 16:44 | #7 |
This is my second home
2005 Connoisseur SE 1.8 Turbo,2004 45 1.8 Connoisseur and my beloved 1998 VVC Coupe. Join Date: Nov 2009
Location: Derby.
Posts: 8,762
Thanks: 2,022
Thanked 1,016 Times in 739 Posts
|
Buy a new valve and split it at the large nut so the tail and body separate. Do the same with the existing one.You will need to hold against the body while undoing the large nut.Introduce the new valve body to the existing tail and tighten.Job done,no need to undo water connection.Just take care you don't loose the aperture and piston from the new valve while apart.
__________________
|
5th November 2019, 18:33 | #8 |
Avid contributor
Rover 75 Tourer cdt Join Date: Sep 2014
Location: Wolverhampton
Posts: 176
Thanks: 51
Thanked 57 Times in 39 Posts
|
[QUOTE=stevestrat;2773608]Its a slightly weird, hybrid, system. Mains water feeds a combi boiler, kitchen etc, the tank seems to only feed the cold tap on the bathroom sink and toilet, maybe the shower as well I object to getting someone in for what is a simple job, its just getting at the bl00dy thing, dumb idea to put it at the back of the tank! The valve is entitled to be tired, it probably dates from when the cottages were originally renovated about 50 years ago.
From your description it would seem that your bathroom's cold plumbing is piped up as a low pressure system, ( tank fed ). This was sometimes done so that early mixer shower valves and bath mixer taps were operating on equal pressures when being used. I assume that when the combi boiler was fitted the existing shower valve was not compatible to the new boiler, and therefore left to run on the low pressure set up. A solution to your problem may be to change the shower valve to a combi compliant model, then reconnect your low pressure cold supply to the toilet, basin and bath back onto the cold main. You would then be able to terminate the use of the tank. It sounds slot of work, but to connect the low pressure cold could easily be done in the roof space by redirecting the cold mains supply to the tank to connect onto the low pressure cold pipe from the tank. Hope this makes sense. |
6th November 2019, 18:17 | #9 |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Bite the bullet, get somebody in.--If, as you say, it's a simple job the cost will be low.
Don't injure yourself, it's just not worth it.-- |
6th November 2019, 18:25 | #10 |
Loves to post
Rover 75 Saloon Join Date: Mar 2017
Location: Newtown
Posts: 415
Thanks: 273
Thanked 95 Times in 65 Posts
|
I agree with Colvert, get a plumber in!
|
|
|