|
||
|
|
18th January 2015, 12:46 | #1 |
Avid contributor
MG ZT CDTi Join Date: May 2013
Location: Exford
Posts: 173
Thanks: 49
Thanked 25 Times in 20 Posts
|
Another ABS thread!.... More Abs woes....
My speedo has stopped working and my ABS light is on.... its an MG ZT diesel......
I've replaced the ABS sensor on the drivers side this morning, twice, with two new ones I had in the attic, this was after freezing outside drilling out the old one which refused to give in to me! The original problem seemed to be damage to the cable, because I twisted it about where the outer sheath had been worn through, and the ABS light went off.. But neither of the new cables seems to be working.... any suggestions Thanks & regards Phil |
18th January 2015, 12:53 | #2 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
if you drilled it out you may have drilled too deep and damaged the bearing
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
18th January 2015, 13:08 | #3 |
Avid contributor
MG ZT CDTi Join Date: May 2013
Location: Exford
Posts: 173
Thanks: 49
Thanked 25 Times in 20 Posts
|
Thanks, but pretty sure I didn't go to deep as I removed the 'sensor' end intact when pulling out the remains of the unit with pliers..... any way I would know for sure?
|
18th January 2015, 13:34 | #4 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
18th January 2015, 13:49 | #5 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
18th January 2015, 13:59 | #6 |
Newbie
MG ZT-T Join Date: Oct 2014
Location: Norwich
Posts: 24
Thanks: 1
Thanked 0 Times in 0 Posts
|
I'm not the most informed on these matters, but my ABS suddenly became faulty on the front nearside. I traced as you a faulty outside wiring.
Unlike you I couldn't drill mine out and had to get a secondhand hub fitted as even the garage couldn't get it out. What they did find though was that just beyond the plug that vanished into the engine bay there had been a short and the wires had fused. A replacement plug cut and shut and new ABS sensor from a well known auction site resolved it all. Light now out and my cruise control is working again |
11th October 2015, 18:39 | #7 | |
This is my second home
75 Tourer 2.5 Auto, 1.8T, 75V8ZT Join Date: Jun 2007
Location: Johannesburg ZA
Posts: 6,200
Thanks: 1
Thanked 859 Times in 613 Posts
|
Quote:
Even if the OP was not be the smartest tool in the shed, he would have to be rather stupid to do that.
__________________
Worth his V8 in gold |
|
10th October 2015, 21:52 | #8 |
Avid contributor
MG ZT CDTi Join Date: May 2013
Location: Exford
Posts: 173
Thanks: 49
Thanked 25 Times in 20 Posts
|
More Abs woes....
Back in February I had problems with my ABS light, eventually I had a garage replace the drivers front wheel bearing & cable ( at least I think they replaced the wheel bearing!), all OK until a couple of weeks ago...
My speedo started to work intermittently, then my ABS light came on again. Now I have no speedo, a permanent ABS light and am miffed! I replaced the ABS cable today, but the light has not gone out and the speedo is still dead... and unlike the last time, I extracted the old lead without damaging it and having to drill out the remains! so no chance of damaging the bearing ......any suggestions on what I might check? Advice appreciated as always..... thanks ( MG ZT CDTi ) |
10th October 2015, 22:09 | #9 |
Loves to post
MG-ZT Join Date: Aug 2014
Location: Dunfermline
Posts: 474
Thanks: 43
Thanked 83 Times in 70 Posts
|
|
11th October 2015, 00:55 | #10 |
This is my second home
None * DROWNED Join Date: Aug 2007
Location: Cardigan
Posts: 33,339
Thanks: 1,257
Thanked 1,664 Times in 1,081 Posts
|
Threads merged as they are related.
__________________
Andrew Ich Dien Problem solving is... lateral thinking SEARCH FIRST ...ASK LATER... |
|
|