|
||
|
||
|
![]() |
#1 |
Newbie
MG ZT-T Join Date: Mar 2023
Location: Wiltshire
Posts: 23
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]() So I am halfway through a plan to install a heated steering wheel.
I've got the wiring from the battery sorted and I've already got the wheel retrimmed with heated elements in and tested it's all working. My issue is now that I need to wire through the clock spring or find a way to bypass whilst still allowing for the rotation of the steering wheel. I've thought of a few different ways but none of it makes sense without adapting the clock spring. I have seen there are two spare pins in the connector to the clock spring and wondered if they were connected to anything the other side? The other thing I've seen mentioned is that splicing in to the horns/controls and activating anything will set the horn off until the ignition is switched off again? Any help would be much appreciated please see attached images for context!
__________________
WiltshireTouring on TikTok |
![]() |
![]() |
![]() |
#2 |
Gets stuck in
MG ZT Join Date: Jul 2014
Location: Liverpool
Posts: 869
Thanks: 180
Thanked 248 Times in 189 Posts
|
![]() The spare pins are for cruise control. I'm not an expert but unless the power required for your heated wheel is above what the clocksprings can handle it should be ok to use the cruise pins. There are a few members who will be able to confirm this either way. Nice modification though, hope it's as easy as it appears
![]() Lee.
__________________
[SIGPIC][/SIGPIC] |
![]() |
![]() |
![]() |
#3 |
Newbie
MG ZT-T Join Date: Mar 2023
Location: Wiltshire
Posts: 23
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]() Thanks Lee! I've had a look on the dodgy eBay listing for the heated elements and it only states it's a 12v powering the two 18w heated pads.
If the cruise wiring is the other side I could splice into that as the car never came with it as a function and it's not a daily so wouldn't need the function anyway.
__________________
WiltshireTouring on TikTok |
![]() |
![]() |
![]() |
#4 | |
Posted a thing or two
Alpina D3 Join Date: Sep 2014
Location: Cheslyn hay
Posts: 1,004
Thanks: 58
Thanked 294 Times in 227 Posts
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#5 | |
Gets stuck in
MG ZT Join Date: Jul 2014
Location: Liverpool
Posts: 869
Thanks: 180
Thanked 248 Times in 189 Posts
|
![]() Quote:
Lee.
__________________
[SIGPIC][/SIGPIC] |
|
![]() |
![]() |
![]() |
#6 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,446
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
![]() Hello Laurence,
Your two 18 watt heating elements will draw about 3 amps. The rotary coupler (clock spring) currently handles the radio and cruise control controls plus the horn buttons in a relay coil circuit. All these are very low current consumers, nothing approaching 3 amps. I therefore doubt that the rotary coupler has been manufactured to carry such a load. You should therefore accept Lee's kind offer of testing the circuit using his spare coupler. Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
![]() |
![]() |
![]() |
#7 |
Newbie
MG ZT-T Join Date: Mar 2023
Location: Wiltshire
Posts: 23
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]() Thanks guys, a couple of the techs at work were a bit dubious of the power the coupler could take. I do have a spare one so thank you for the offer Lee!
The other option would be to get some higher gauge wire going through the coupler to the unused cruise control pins or to try and have a hole straight through the bottom of the wheel and some sheathed slack wiring to allow for the rotation. Those are my last options I think
__________________
WiltshireTouring on TikTok |
![]() |
![]() |
![]() |
#8 |
Gets stuck in
MG ZT Join Date: Jul 2014
Location: Liverpool
Posts: 869
Thanks: 180
Thanked 248 Times in 189 Posts
|
![]() You have the wheel now, so no going back
![]() Defeat is not an option, when you find a way and you will, please post your solution on here. Heated steering wheel is on my to do list now. Lee.
__________________
[SIGPIC][/SIGPIC] |
![]() |
![]() |
![]() |
#9 |
This is my second home
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4. Join Date: Jul 2009
Location: Hampshire
Posts: 11,565
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
|
![]() Well as mentioned the rotary coupler is designed to handle signal currents. I had one apart a couple of years ago and the ribbon was very thin, so it's good news - the coupler will probably contribute more to the steering wheel heating than your elements, before it gives up the ghost.
![]() |
![]() |
![]() |
![]() |
#10 |
Posted a thing or two
R 75 Tourer diesel Conny 2002, V6 Conny saloon petrol 2003 Join Date: Mar 2013
Location: Taunton
Posts: 1,135
Thanks: 212
Thanked 406 Times in 223 Posts
|
![]() Gloves out of fashion?
__________________
Rover 75 Tourer Conny 2002 remapped 160 auto, R75 V6 2.5L auto Connoisseur 2003 |
![]() |
![]() |
![]() |
|
|