Go Back   The 75 and ZT Owners Club Forums > The 75 and ZT Owners Club Forums > Technical Help Forum
Register FAQ Image Gallery Members List Calendar Mark Forums Read
Notices

Reply
 
Thread Tools Display Modes
Old 25th October 2013, 15:39   #1
David Lawrence
This is my second home
 
Rover 75 CDT-2001

Join Date: Jan 2009
Location: Wrexham, North Wales
Posts: 3,606
Thanks: 195
Thanked 606 Times in 501 Posts
Default Replacing Alternator Brushes with Alternator still on the car

Thanks to the excellent suggestion from Mike Noc, I can confirm that it is possible to replace alternator Brushes with the alternator left on the car, and here are a few of the steps I followed for my 2001 CDT Alternator YLE102500 (2001 Valeo model)

All done from the top of the engine bay, I didn't remove the undertray today as Mike had suggested because the yard was very wet and I didn't fancy scraping around in the wet, but it may help you to see what you are doing but the principles will be the same as my way.

Start by disconnecting the Battery.

1. Remove engine cover
2. Remove air intake duct (This helps you get your arms in at the right angle for removing bolts on the alternator)
3. Remove the single bolt securing the top of the dip stick tube (This just helps you get a long handled socket driver in at the right angle for one or two of the bolts)

4. Using a long flat driver, pull up the retaining wire clip an remove it. keep a finger on it to save it pinging off in to the depths.
5. Remove the small 3 pin connector. From what I've learned the connector is a 3 pin one, but only 2 pins have wires in them. The alternator has 3 pins on in with this model. Dont know what the un-used pin does. But this answers why Rimmers can offer the later 2 pin version as an alternative now.

6. Using a 13mm socket on a driver, (I used a 1/4 drive one) remove the brass nut holding the thick black supply cable. Remove the cable from the alternator and lodge it out of the way until time to refit.

7. You are now looking for 3 8mm brass nuts that hold the alternator rear cover on
DSCN0164.JPG



This picture shows the alternator after removing the 3 nuts and the cover. The 3 nuts are the one above the big supply stud in between the 3 pin connector and the stud, one almost vertically below the big stud near the bottom, and one parallel with that on on the right hand side. The other ones only become visible after removing the cover.


8. With those 3 nuts removed you can just wriggle the cover over the studs and out of the engine bay. If like mine it will be caked in thick black oil.

9. To understand the next bit take a look at this link for a brand new Voltage Regulator to fit this particular model
http://www.vehicleelectricsshop.co.u...BMW_ROVER.html



You see the 2 small ring tabs. Then the 2 bigger metal washers at each side. So first remove 2 more 8mm nuts from either side of the regulator.

10. Next you need to remove what looks like a black foam rubber gunge which is covering 2 small 7mm brass screws securing the 2 small ring tabs.

It goes without saying to make sure you dont drop any of these screws or nuts.

11. With these removed, the regulator will now pull away from the alternator and can be removed to a workbench for repair.

12. Next inspect the brushes. Mine were badly worn.
here is a picture of the old and the new.
DSCN0171.JPG




One Brush still had a little life left in it, but the other had disintegrated at the end. New ones were 4 times longer, purchased from here:
http://www.jcrsupplies.co.uk/product..._REF_5221.html

Arrived very next day for about £6 including delivery.

13. I drilled a small 2mm hole through the end of the Brush terminal and the old brushes just fall out. There is a small black Brush cover holding them in at this point which with a little encouragement you can slide off the regulator. It looks fragile so be careful with it.

14. With the old brushes out, be careful not to lose the pressure springs then thread the copper wires for the new brushes back through the 2mm hole you drilled, then I filed a slight groove in the terminal post and wrapped the wires tightly around it before soldering both brushes on to the posts, so they have a firm solder joint and also a mechanical fix.

15. Now go back to the car and clean up the slip rings. Mine were caked with the disintegrated old brush, and I brushed this off with a small paint brush.

16. Now refit everything in reverse order to removal. The Brushes can be tricky to get started, as they protrude under pressure of the spring and need to be gently pushed back in with a small driver until you get the regulator module back in position, but when you try it you'll see what you need to do.
My slip rings had grooves in them but the new brushes fitted perfectly in to them, and so I hope will give me a reasonable service life yet.

Now that I know exactly where the bolts are, and how it comes apart I reckon i could do the job in just over 1 hour next time. What I also learned doing this job is that at least the full regulator module is available should it become necessary.

As I said at the start, if you were to take the engine undertray off, and go at this job from below with a decent set of ramps you may find access easier, but not what I wanted on a soaking wet yard. I hope this will both encourage others with Brush failure, and at least confirm that it is possible in-situ avoiding the need for belt removal and additional expense of 24mm ring spanners etc, which I don't have to hand and would have needed to buy one from Halfords at £9.99 !!!

The downside to doing this in such a cramped space was opportunity for photo taking was pretty limited.


P.S. Mike Noc - I owe you one !

Last edited by Dragrad; 31st July 2014 at 00:24.. Reason: Thumbnails enlarged - Pic from link added
David Lawrence is offline   Reply With Quote
Old 25th October 2013, 16:33   #2
Jules
This is my second home
 
ZT 260 SE Twilight and 10 other 75 ZT's :O

Join Date: Jan 2007
Location: Conwy NORTH WALES
Posts: 11,094
Thanks: 512
Thanked 1,116 Times in 763 Posts
Default

Nice on David
Glad I kept a few old Valeos
__________________
[SIGPIC][/SIGPIC]


Newbies do now!!
1. Plenum drains..all 3 or 4 year dependent
2. Cooling fan..All speeds functioning
3. Bonnet cable divider block
Jules is offline   Reply With Quote
Old 25th October 2013, 17:50   #3
FrenchMike
This is my second home
 
FrenchMike's Avatar
 
Rover 75 Saloon

Join Date: Aug 2007
Location: Avignon
Posts: 4,466
Thanks: 94
Thanked 661 Times in 554 Posts
Default

Simply excellent ...

Has to be put in the 'how to' folder ...

Mike

Last edited by FrenchMike; 25th October 2013 at 17:53..
FrenchMike is offline   Reply With Quote
Old 25th October 2013, 20:04   #4
DMGRS
Discount MG Rover Spares
 
DMGRS's Avatar
 
Rover 75 CDTi, 2x MG ZS180

Join Date: Jun 2011
Location: Hythe, Southampton
Posts: 11,317
Thanks: 456
Thanked 3,377 Times in 2,027 Posts
Default

Ordered a set! Thank you!

Gawd I love this community.
__________________



Your trusted MG Rover specialist!
Tel: 02380 001133 / Email: [email protected]

We now have a 'chat' function on our site for even quicker replies. Give it a try!

Remember - discount code FORUM5 for 5% off
DMGRS is offline   Reply With Quote
Old 25th October 2013, 22:19   #5
Mike Noc
This is my second home
 
Mike Noc's Avatar
 
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4.

Join Date: Jul 2009
Location: Hampshire
Posts: 11,531
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
Default

Superb result David. I didn't suggest removing the undertray either though - just the acoustic cover which is the top engine cover.

On my alternator the brush cover will hold the brushes off the slip rings if you don't push it fully home until after the regulator is bolted back on, but I'm not sure if they are all like this.

Great 'How To'. Should save people loads of time and hassle.
Mike Noc is offline   Reply With Quote
Old 25th October 2013, 22:48   #6
brianw
Gets stuck in
 
brianw's Avatar
 
Rover 75 CDT Connoisseur SE Rover 75 1.8 Auto Connie

Join Date: Nov 2011
Location: Aldershot
Posts: 921
Thanks: 126
Thanked 119 Times in 79 Posts
Default

A very informative post.
Thank you.
I think perhaps I should get some brushes 'just in case'
brianw is offline   Reply With Quote
Old 26th October 2013, 00:17   #7
Avulon
This is my second home
 
1.8t Tourer

Join Date: Oct 2011
Location: Tanelorn
Posts: 4,830
Thanks: 956
Thanked 1,148 Times in 916 Posts
Thumbs up

Well done David, this should definitely go into the how to section. And also Respect to Mike Noc as well for the suggestion and prelim work.

__________________
Need a T4 ?: T4 Owners Map thanks to Stevestrat ( use at your own risk)

Where?:
https://en.wikipedia.org/wiki/Tanelorn
Mods/Retrofits:

PCV vortex 'filter'; bluetooth; inline thermostat; reversing sensors; plenum spyhole ; headlamp washers ; Diy mp3 player replacing CD multichanger; FBH with remote; Headlamp washers; black/chrome front grille, rear blind; Xenon projectors
To do:
puddle lights; 2 Din cd/nav to fit; boot release button
Avulon is offline   Reply With Quote
Old 26th October 2013, 04:31   #8
David Lawrence
This is my second home
 
Rover 75 CDT-2001

Join Date: Jan 2009
Location: Wrexham, North Wales
Posts: 3,606
Thanks: 195
Thanked 606 Times in 501 Posts
Default

Quote:
Originally Posted by Mike Noc View Post
Superb result David. I didn't suggest removing the undertray either though - just the acoustic cover which is the top engine cover.

On my alternator the brush cover will hold the brushes off the slip rings if you don't push it fully home until after the regulator is bolted back on, but I'm not sure if they are all like this.

Great 'How To'. Should save people loads of time and hassle.

Mike,

My brush cover had a little step in it that stopped it half way closed, so I guess if there was a suitable tool you could insert it at that stage to hold the brushes in then remove it prior to pushing it down the rest of the way, but when you do this job in situ, the brushes are pointing forward so it is just as easy to push them down one at a time with a screw driver. Then fit the cover afterwards.

this fix will keep the alternator going until the slip rings go, but now I have time to get properly prepared for replacement. The worst thing about these jobs is that they happen when you have no time to sort them out. And worse, don't have the parts or the equipment to hand to do it either. This requires the minimal tools really. The only thing some people may not have is a soldering iron. In my case i was short of a spare alternator and a 24mm spanner, both of which I intend to solve before it happens again.
David Lawrence is offline   Reply With Quote
Old 26th October 2013, 08:29   #9
Mike Noc
This is my second home
 
Mike Noc's Avatar
 
Rover 75 CDT Manual Connoisseur SE, Rover 75 CDT Automatic Connoisseur SE & a Freelander Td4.

Join Date: Jul 2009
Location: Hampshire
Posts: 11,531
Thanks: 3,470
Thanked 3,119 Times in 2,247 Posts
Default

Hopefully you should get a fair few miles yet from the slip rings David.

My alternator had covered around 340k miles and although the brushes had worn away and there was wear on the slip rings they still had some way to go.

As for the rotor bearings they felt as good as new.

Will report back on how easy the slip ring change is when I get the time to do it.
Mike Noc is offline   Reply With Quote
Old 26th October 2013, 08:47   #10
David Lawrence
This is my second home
 
Rover 75 CDT-2001

Join Date: Jan 2009
Location: Wrexham, North Wales
Posts: 3,606
Thanks: 195
Thanked 606 Times in 501 Posts
Default

Quote:
Originally Posted by Mike Noc View Post
Hopefully you should get a fair few miles yet from the slip rings David.

My alternator had covered around 340k miles and although the brushes had worn away and there was wear on the slip rings they still had some way to go.

As for the rotor bearings they felt as good as new.

Will report back on how easy the slip ring change is when I get the time to do it.

On the website of one component supplier is a video:
http://www.youtube.com/watch?v=f56-26I6idc

Not sure if our alternators are the same as this as I didn't delve this deep in to mine, but looks easy enough on a bench.

So unless the field coils go, it seems these alternators have virtually all the parts available for doing the home refurb. Bearings as well. Like yours, my bearings are still smooth at 167,000. A mere novice really.
I might pick up a cheap second hand one from a scrappy and a set of parts to refurb it. Then it strengthens the chance that because I'm prepared, I won't ever need it.
David Lawrence is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 12:34.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright © 2006-2023, The Rover 75 & MG ZT Owners Club Ltd