|
||
|
3rd August 2016, 07:23 | #1 |
Posted a thing or two
Rover 75 1.8t Join Date: Oct 2015
Location: Edinburgh
Posts: 1,377
Thanks: 384
Thanked 409 Times in 267 Posts
|
Holts Gun Gum for blowing backbox ?
How'do folks
My car has been running well since her head gasket repair However - mot is due in 4 weeks ....... will she pass I have a new cat to be fitted before then as the one on the car is goosed. but i've noticed a couple of wee holes in the backbox, it's the original exhaust and the whole of the outer skin is gone has anyone any experience of Holts Gun Gum ? and would a repair such as this be likely to pass mot inspection ? i assume, as long as it doesn't leak exhaust gases it would be fine ? this will be the first time i take a car for an mot Paul........ |
3rd August 2016, 07:32 | #2 |
Avid contributor
ZT CDTI / 1951 Healey Tickford Drop Head Join Date: Jun 2014
Location: Brighton
Posts: 207
Thanks: 19
Thanked 28 Times in 23 Posts
|
Gun Gum might work and hold on long enough for the MOT, it might work for a year but might fall out in 10 mins!
|
3rd August 2016, 08:50 | #3 |
Avid contributor
Rover 75 Saloon Join Date: Dec 2015
Location: Berkshire
Posts: 110
Thanks: 3
Thanked 24 Times in 22 Posts
|
Gun Gum will struggle to stay in place - the gas pressure will likely blow it straight out.
If you use it and cover with an exhaust bandage then you will have a better chance of it sealing up and staying in place until at least after the MoT. However, if you are going to all the trouble of replacing the cat then the backbox is an easy 10 minute job. |
3rd August 2016, 08:56 | #4 | ||
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,637
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
Quote:
Quote:
Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
||
3rd August 2016, 09:03 | #5 |
Gets stuck in
Rover 75 2.5 V6 in Wedgwood Blue Join Date: Dec 2015
Location: Felbridge, East Grinstead
Posts: 982
Thanks: 250
Thanked 294 Times in 206 Posts
|
A combination of gun gum, aluminium foil and exhaust bandage will probably sort it. Make sure you just let the engine tick over, or take it for a very gentle drive, for the first 20 minutes or so after you've applied it. Otherwise it will blow out before it's set. You could replace the rear box. As others have said, it's not a massive job (just make sure you give those hangers a good lubrication).
What does seem to be a recurring theme with others though is that, unless you spend the dough on an original box, there does seem to be an issue with resonance resulting in an unwelcome booming noise usually between 1500 and 2200 revs. This may simply be because cheaper boxes aren't made to the same standard. My thoughts are that it's a combination of that and the fact that the boot floor and bumper create a little echo chamber on four sides of the rear box which amplifies the sound. I'm going to have a go with various sorts of muffling and see if it makes a difference. So in short, how much do you want to pay and what (beyond getting through the MOT) is your preferred result?
__________________
Conformity is not morality. Consensus is not truth. |
3rd August 2016, 09:09 | #6 |
Posted a thing or two
Rover 75 1.8t Join Date: Oct 2015
Location: Edinburgh
Posts: 1,377
Thanks: 384
Thanked 409 Times in 267 Posts
|
cheers folks
i'd ideally like to change the backbox (it will be replaced asap) however i don't have funds to do this before the mot so off to halfords for Gun Gum it is we'll see how it goes.......i figure if i do it now, i'll have a couple of weeks to see if it does the job and holds up - if not, i'll have a bit of time to see what i can do r.e replacement backbox. Paul........ |
3rd August 2016, 09:26 | #7 | |
Posted a thing or two
Rover 75 1.8t Join Date: Oct 2015
Location: Edinburgh
Posts: 1,377
Thanks: 384
Thanked 409 Times in 267 Posts
|
Quote:
I've read a few posts relating to this - i'd ideally like my car to be quiet and refined like a Rover should at the minute i don't have much option, i have a replacement cat already and just about enough cash to have this fitted (the cat on the car is goosed and unlikely to pass emissions) the backbox has a slight blow, and the holed areas i can see are pretty small - so if she can get past the mot for now i'll be happy - i'll possibly try and get the quietest stainless catback system made up, as it seems (from others experience) almost impossible to match the original set-up for quietness. Paul.... |
|
3rd August 2016, 10:00 | #8 | |
This is my second home
CDTi Conniosseur SE HLNav Tourer and a Personal Line CDT Conniosseur SE Tourer..for the time being. Join Date: Jul 2010
Location: Cumbria
Posts: 3,639
Thanks: 340
Thanked 423 Times in 294 Posts
|
Quote:
Re Gun Gum: perfect for what you need. Clean up the repair area, keep moist with a wet cloth, follow the instructions and BE QUICK after you mix the 2 parts. It works easily for a while and then....................goes off in a matter of seconds in your hands. |
|
3rd August 2016, 11:02 | #9 | |
Posted a thing or two
Rover 75 1.8t Join Date: Oct 2015
Location: Edinburgh
Posts: 1,377
Thanks: 384
Thanked 409 Times in 267 Posts
|
Quote:
does the Gun Gum Paste require a separate hardener ? i picked up a tin of the paste - haven't opened the tin yet to see if it's a 2 part mix, i'd assumed it was premixed ready to go as no mention of a mix on the tin and i never seen a separate hardener to buy Paul........ |
|
3rd August 2016, 11:41 | #10 | |
This is my second home
CDTi Conniosseur SE HLNav Tourer and a Personal Line CDT Conniosseur SE Tourer..for the time being. Join Date: Jul 2010
Location: Cumbria
Posts: 3,639
Thanks: 340
Thanked 423 Times in 294 Posts
|
Quote:
The stuff I kept my Lexus LS400 exhaust going on was http://www.4yourhomeuk.com/quiksteel...cRPxoCgwXw_wcB It comes in a plastic tube about 3 1/2" long containing 2 parts: 1 grey 1 black. You cut off an equal amount form each part and mix the 2 together in your hand. Hard work at first, then it gets easy and you think "this is ok, I'll take my time". Then, suddenly, it sets hard in seconds. And it sets as hard as steel. I used it to rebuild the manifold to exhaust pipe flanges that had all but rotted away. It is amazing stuff. |
|
|
|