|
||
|
14th October 2019, 23:54 | #1 |
Avid contributor
1999 Rover 75 2.5 Connoisseur saloon Join Date: May 2007
Location: Carterton, NZ
Posts: 106
Thanks: 18
Thanked 3 Times in 3 Posts
|
Upper manifold on V6
I am about to replace my noisy manifold with a spare quiet one. Should I dismantle and clean out the spare before fitting?
__________________
1999 Rover 75 Connoisseur 2005 Rover 75 Connoisseur SE 1970 Rover 2000TC 1973 Rover P5B Coupe 1962 Rover P4 - 100 |
15th October 2019, 00:16 | #2 |
Gets stuck in
MG ZT-T Join Date: Jun 2016
Location: White Rock, BC on Canada's Pacific Coast
Posts: 849
Thanks: 338
Thanked 367 Times in 210 Posts
|
The problem with dismantling is you basically have to chisel the lid off of it with potential for damage (I have done it and it's a chore) and then glue it back on.
You may be best to just dump a couple of litres of degreaser in it, slosh it around and leave it to evaporate for a few days. (It may be easier if you have an air compressor to blow it out) On the other hand it will be oiled up after a couple of days anyway so probably futile!
__________________
ZT-T190, Anthracite, LHD, Left the Line on June 24, 2002, Sold new in Switzerland, spent time in Germany, Imported to Canada in September 2021 Last edited by Rich in Vancouver; 15th October 2019 at 00:19.. |
15th October 2019, 05:59 | #3 | |
Gets stuck in
Rover 75 2.5 V6 in Wedgwood Blue Join Date: Dec 2015
Location: Felbridge, East Grinstead
Posts: 982
Thanks: 250
Thanked 294 Times in 206 Posts
|
Quote:
These things were constructed in Satan's own workshop using dark forces beyond the comprehension of mortals. Be happy when they work. Shrug stoically when they don't.
__________________
Conformity is not morality. Consensus is not truth. |
|
16th October 2019, 21:50 | #4 |
Avid contributor
1999 Rover 75 2.5 Connoisseur saloon Join Date: May 2007
Location: Carterton, NZ
Posts: 106
Thanks: 18
Thanked 3 Times in 3 Posts
|
Thanks for the very useful comments. Will leave well alone.
__________________
1999 Rover 75 Connoisseur 2005 Rover 75 Connoisseur SE 1970 Rover 2000TC 1973 Rover P5B Coupe 1962 Rover P4 - 100 |
17th October 2019, 00:45 | #5 |
Gets stuck in
MG ZT-T Join Date: Jun 2016
Location: White Rock, BC on Canada's Pacific Coast
Posts: 849
Thanks: 338
Thanked 367 Times in 210 Posts
|
I should have mentioned that the manifold that I opened up and sealed back up doesn't work worth a darn. I'm not sure if it was my fault or not but there is too much drag on the valve operating rod. One day I may open it up again and see what's going on but as Lord of Hog says they really are the spawn of the devil so I will continue shrugging stoically as long as my current one works.
__________________
ZT-T190, Anthracite, LHD, Left the Line on June 24, 2002, Sold new in Switzerland, spent time in Germany, Imported to Canada in September 2021 |
4th November 2019, 20:27 | #6 |
Regular poster
2001 and 2004 Rover 75's Join Date: Jun 2018
Location: Buderim QLD
Posts: 47
Thanks: 18
Thanked 3 Times in 2 Posts
|
Replacing the inlet manifold
I know this is a well discussed topic. I assume that the only sensible way to go is to buy a new one or take the guts out of the existing one. Is there any other option? I just grin and bear in my 2004 KV6 with 100,000kms.
|
4th November 2019, 20:33 | #7 |
Premium Trader
Rover 75 Join Date: Nov 2010
Location: Devon
Posts: 33,760
Thanks: 8,837
Thanked 14,831 Times in 8,030 Posts
|
No other option other than the ones you have mentioned I'm afraid, there was someone on FB developing alloy inlets but I'm not sure how far that got?
__________________
Lest we forget..
|
4th November 2019, 20:44 | #8 |
This is my second home
Roverless + 1.7D Sportage Join Date: Aug 2014
Location: East Norfolk
Posts: 7,050
Thanks: 729
Thanked 2,021 Times in 1,449 Posts
|
I wonder what Kia used on the Magentis?
https://www.ebay.co.uk/itm/INTAKE-MA...wAAOSwWv5Z5zw7 No VIS ?
__________________
Oil in my veins! Last edited by roverbarmy; 4th November 2019 at 20:46.. |
7th November 2019, 23:26 | #9 |
Avid contributor
1999 Rover 75 2.5 Connoisseur saloon Join Date: May 2007
Location: Carterton, NZ
Posts: 106
Thanks: 18
Thanked 3 Times in 3 Posts
|
Catch tank
What are the thoughts on fitting an oil catch tank to prevent oil getting into the manifold? Any recommendations would be appreciated.
__________________
1999 Rover 75 Connoisseur 2005 Rover 75 Connoisseur SE 1970 Rover 2000TC 1973 Rover P5B Coupe 1962 Rover P4 - 100 |
8th November 2019, 02:18 | #10 |
Gets stuck in
MG ZT-T Join Date: Jun 2016
Location: White Rock, BC on Canada's Pacific Coast
Posts: 849
Thanks: 338
Thanked 367 Times in 210 Posts
|
I fit an oil catch tank on my V6 Freelander. It certainly collected fluid but the manifold still got oily. I found if I forget to empty the tank every couple of weeks, and it overfilled the car would run terribly.
More than once I thought it had a major issue when it was just choking on the slop in the can. Eventually I just removed the catch tank and fitted a pair of sealed VIS motors.
__________________
ZT-T190, Anthracite, LHD, Left the Line on June 24, 2002, Sold new in Switzerland, spent time in Germany, Imported to Canada in September 2021 |
Thread Tools | |
Display Modes | |
|
|