FaceLift bonnet catch

Kandyman · 2nd March 2007, 13:18

Hi All,
I am after a part number for a FaceLift bonnet catch as i will have to change mine over at some stage from a pre facelift, also any ideas how to change it over ?
Utill i see the part i'm a bit

as to how it fits.

Cheers

JohnDotCom · 2nd March 2007, 13:41

These are all the Part Numbers and descriptions for all the Bonnet release parts that make up the Facelift Model.

FSE000130 Cable assembly-bonnet release assembly
FSE000140 Cable-bonnet release assembly
FSE000150 Cable-bonnet release assembly
FTI100000 Coupler-bonnet release cable
FPC100190 Catch assembly-bonnet safety
FPC000010 Catch assembly-bonnet safety
FPC000050 Catch assembly-bonnet
FS106127 Screw-flanged head - M6 x 12 - bonnet catch
FPS100441 Latch assembly-bonnet - burglar alarm.
FS106307 Screw-flanged head - M6 x 30 - bonnet latch
FPJ100170 Striker-bonnet
FYG10007 Bolt-washer - M6 x 10 - bonnet striker
FSC100340PMA Lever assembly-bonnet release assembly
SYC101000 Clip-cable
FTU000010 Housing - Bonnet Release Coupler
FTX000010 Shuttle - Bonnet Release Coupler

Some of the Repeated Parts are for if you have the MG Badge or Rover Badge & Grill etc let me Know what front you are putting on for the Correct Reference. Some are done by Serial Number also.

Kandyman · 2nd March 2007, 13:48

And in english ?

JohnDotCom · 2nd March 2007, 14:01

Quote:

Originally Posted by Kandyman

And in english ?

Not my intention to confuse Kandyman sorry,
You would need Part Number: FPC000050 Catch assembly-bonnet.
Which is the Facelift MG release Lever/Button under Bonnet.
The reason for the Complete List as shown in Post 2 is that some parts have different Part Numbers to those on MK1 so not sure if they fit directly or need to be changed.
Im sure Alex may Know if they switch direct or anybody else who has changed out there.

Kandyman · 2nd March 2007, 14:06

Thanks for tidying up post 2 it makes a bit more sense now

I'm hoping it's just a swap over of the Catch assembly.

Any one care to assist with a little How To

Rich · 2nd March 2007, 14:39

Hi.

Could you not fit a ZT one instead of a facelift one?

I'm guessing this is for the meshing that's also holding up my plans too

JohnDotCom · 2nd March 2007, 14:45

The Facelift one as you are most Probally aware does not come through the Grill area at all it only becomes visible with the Bonnnet released and then more of a push lever/button than the other Pull type which sits in Cutout in Cross Member.

You can see the Small push lever on the Cross member on the L/H side.

https://www.the75andztclub.co.uk/forum/

salop75 · 2nd March 2007, 14:52

That is the bonnet catch i have on my 03 MK1, odd.

John

JohnDotCom · 2nd March 2007, 15:00

Strange as The Part number for this one 2005 model is differrent from the earlier ones, but it did change from S/No: 271837 which would appear to be the same on some Pre Facelift models. Im sure Ive seen it was moved from Grille on earlier Threads.

baxlin · 3rd March 2007, 07:50

Engine bay looks clean JDC - I take it it is yours and not a library piccy? Apologies in advance if I cast doubt!!

Malcolm

2nd March 2007, 13:18	#1
Kandyman Banned ROVER 75 2.5 V6 Connoisseur SE Limousine 2004 Join Date: Oct 2006 Location: Welling Posts: 10,995 Thanks: 0 Thanked 2 Times in 2 Posts	FaceLift bonnet catch Hi All, I am after a part number for a FaceLift bonnet catch as i will have to change mine over at some stage from a pre facelift, also any ideas how to change it over ? Utill i see the part i'm a bit as to how it fits. Cheers

2nd March 2007, 13:41	#2
JohnDotCom * Rover 75 FaceLift Tourer CDTi 170BHP Auto ConnSE 2005 Model Starlight Silver Join Date: Nov 2006 Location: Abergele Posts: 28,735 Thanks: 0 Thanked 6 Times in 5 Posts	These are all the Part Numbers and descriptions for all the Bonnet release parts that make up the Facelift Model. FSE000130 Cable assembly-bonnet release assembly FSE000140 Cable-bonnet release assembly FSE000150 Cable-bonnet release assembly FTI100000 Coupler-bonnet release cable FPC100190 Catch assembly-bonnet safety FPC000010 Catch assembly-bonnet safety FPC000050 Catch assembly-bonnet FS106127 Screw-flanged head - M6 x 12 - bonnet catch FPS100441 Latch assembly-bonnet - burglar alarm. FS106307 Screw-flanged head - M6 x 30 - bonnet latch FPJ100170 Striker-bonnet FYG10007 Bolt-washer - M6 x 10 - bonnet striker FSC100340PMA Lever assembly-bonnet release assembly SYC101000 Clip-cable FTU000010 Housing - Bonnet Release Coupler FTX000010 Shuttle - Bonnet Release Coupler Some of the Repeated Parts are for if you have the MG Badge or Rover Badge & Grill etc let me Know what front you are putting on for the Correct Reference. Some are done by Serial Number also. Last edited by JohnDotCom; 2nd March 2007 at 13:53..

2nd March 2007, 14:39	#6
Rich Posted a thing or two http://Roadca.ms - Letting you see what they see! Join Date: Nov 2006 Location: Yup Posts: 1,786 Thanks: 0 Thanked 7 Times in 1 Post	Hi. Could you not fit a ZT one instead of a facelift one? I'm guessing this is for the meshing that's also holding up my plans too __________________ https://VehicleGPS.UK http://www.MotorwayCameras.co.uk

2nd March 2007, 14:45	#7
JohnDotCom * Rover 75 FaceLift Tourer CDTi 170BHP Auto ConnSE 2005 Model Starlight Silver Join Date: Nov 2006 Location: Abergele Posts: 28,735 Thanks: 0 Thanked 6 Times in 5 Posts	The Facelift one as you are most Probally aware does not come through the Grill area at all it only becomes visible with the Bonnnet released and then more of a push lever/button than the other Pull type which sits in Cutout in Cross Member. You can see the Small push lever on the Cross member on the L/H side. https://www.the75andztclub.co.uk/forum/ Last edited by JohnDotCom; 2nd March 2007 at 14:55..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

2nd March 2007, 13:48	#3
Kandyman Banned ROVER 75 2.5 V6 Connoisseur SE Limousine 2004 Join Date: Oct 2006 Location: Welling Posts: 10,995 Thanks: 0 Thanked 2 Times in 2 Posts	And in english ?

2nd March 2007, 14:06	#5
Kandyman Banned ROVER 75 2.5 V6 Connoisseur SE Limousine 2004 Join Date: Oct 2006 Location: Welling Posts: 10,995 Thanks: 0 Thanked 2 Times in 2 Posts	Thanks for tidying up post 2 it makes a bit more sense now I'm hoping it's just a swap over of the Catch assembly. Any one care to assist with a little How To

2nd March 2007, 14:52	#8
salop75 Avid contributor Rover 75 2.5 Conn SE Saloon Auto Join Date: Nov 2006 Location: Shrewsbury Posts: 193 Thanks: 1 Thanked 0 Times in 0 Posts	That is the bonnet catch i have on my 03 MK1, odd. John

2nd March 2007, 15:00	#9
JohnDotCom * Rover 75 FaceLift Tourer CDTi 170BHP Auto ConnSE 2005 Model Starlight Silver Join Date: Nov 2006 Location: Abergele Posts: 28,735 Thanks: 0 Thanked 6 Times in 5 Posts	Strange as The Part number for this one 2005 model is differrent from the earlier ones, but it did change from S/No: 271837 which would appear to be the same on some Pre Facelift models. Im sure Ive seen it was moved from Grille on earlier Threads.

3rd March 2007, 07:50	#10
baxlin This is my second home Volvo C70 Convertible and JZR 3 wheeler Join Date: Nov 2006 Location: Tring, Herts Posts: 3,960 Thanks: 124 Thanked 173 Times in 124 Posts	Engine bay looks clean JDC - I take it it is yours and not a library piccy? Apologies in advance if I cast doubt!! Malcolm