|
||
|
16th February 2011, 16:43 | #1 |
Avid contributor
MG ZT 160+ Turbo. MG TF 135 Join Date: May 2008
Location: Livingston
Posts: 169
Thanks: 0
Thanked 0 Times in 0 Posts
|
Number Plate Light PCB Removal
Drivers side Number plate bulb holder has burnt out and I can't work out how to remove the PCB unit. Car is facelift ZT with the lip spoiler, any pointers on how to remove it anyone?
__________________
[SIGPIC][/SIGPIC] |
16th February 2011, 17:49 | #2 |
Banned
MG ZT V6 190+ Join Date: Sep 2008
Location: Leeds
Posts: 33,223
Thanks: 41
Thanked 1,614 Times in 1,416 Posts
|
Remove bootlid felt trim and remove spoiler..
The number plate PCB is secured to the bootlid by automotive double sided tape,carefully remove without causing anymore damage to the contacts |
16th February 2011, 19:04 | #3 |
Avid contributor
MG ZT 160+ Turbo. MG TF 135 Join Date: May 2008
Location: Livingston
Posts: 169
Thanks: 0
Thanked 0 Times in 0 Posts
|
Thanks Pab
__________________
[SIGPIC][/SIGPIC] |
16th February 2011, 19:33 | #4 |
This is my second home
Rover75 and Mreg Corsa. Join Date: Nov 2006
Location: Sumweer onat mote o'dust (Sagin)
Posts: 21,753
Thanks: 341
Thanked 3,660 Times in 2,924 Posts
|
How to Remove and Dismantle the Numberplate Lamp Unit
These notes/photos are based on the facelift/Mk2 model Rover 75. Other models may vary slightly. I'd fitted a pair of 8xSMD LED festoons to illuminate the numberplate and was generally pleased with them. They were reasonably cheap and didn't affect the blown bulb display at all. They weren't sold as CANbus friendly, which usually inflates the price. Anyway after a few weeks one went out, which I thought was odd and a few weeks after that, the other also went out. Knowing that LEDs don't blow like bulbs, I decided that the wintry weather had got into the works and anticipated having tofix the printed circuit board I'd read about. This is the usual cause of numberplate lamp problems. So, here's myphoto record of the job. The numberplate lamp unit is housed within the boot lid lift handle or plinth as I call it. The plinth has to be removedfirst. To access the attachments, you have to remove the lid liner. The liner is held in position by nineteen push fit (fir tree) clips around its edge. You can lever under the head of these with a thin blade. I happened to have a fir tree clip lifting tool as shown in the photo. Image 1 Here's another look at it. I bought this on eBay for a couple of pounds. It's ideal for removing door liner clips, which can be difficult. Image 2 While removing the liner, you'll notice a plastic insert in the upper right corner. This is the emergency boot lockrelease. Yep, you can release a locked boot from inside by dropping down the rear seat squab. Remember that next timeyou lock the keys in the boot. Of course the doors must be unlocked so you can get inside, but it happens. Here's the release puller tab. It slides out of the holder and is attached to the lock with a tough plastic pull-string. Image 3 Here it is after removing the liner. Image 4 With the liner out of the way, you'll find a large opening through which you can pull away the two spade connectors forming the circuit. One is feed, the other earth. They'll fit either way, but naturally stay in position. Next, remove the plinth retaining nuts. There are two conventional flanged nuts either side of centre and two unconventional 'screwits' (my name) at each end. They each require a 10mm socket. The inner nuts are accessed through holes in the boot lid framework as shown below. Image 5 The outer fasteners are accessed through these orifices. Image 6 You may need a small torch to see into the cavity of the lid. Also, before applying the socket, put some sticky stuff into the socket to hold the nuts when they come away. If you drop one into the cavity of the lid, you'll never see it again. For this, I used some very sticky mastic strip designed for fixing double-glazing panels. Again, I happened to have a roll in the garage and decided it was also ideal for refitting the lamp. More on this later. The nuts aren't tight, just slacken them by hand as shown below. Image 7 The inner nuts will come nicely off the captive bolts in the plinth. The two outer screwits need more care because they cut their own thread into the plastic pins at each end of the plinth. Here's the four nuts after careful removal. Image 8 Here's a closeup of a screwit so you can get the gist of it. Image 9 These screwits are basically designed for single use only so a little damage may be caused to the pin when you unscrew them. You have to use some judgement on how much stress to apply, particularly when refitting them. With all four nuts removed, the plinth will simply lift away from the lid. Or at least it shoul. In my case the left end seemed stuck. I assumed the plastic pin was somehow fouling the lid and no amount of gentle pulling would free it. When I looked againusing the torch, there was another screwit still holding onto the pin! They'd screwed two on instead of one! I guess they were nested together when they guy fitted it all. Anyway, that possiblity is worth knowing about and will prevent you damaging thepin as I did. It snapped off during the struggle. Here's the bits. Image 10 and close up: Image 11 With the plinth removed, you'll find the innerlamp unit attached to the lid. It's suck in place with double-sided sticky foam - and it's very well stuck! Image 12 I'd read of people using a hair drier to soften the adhesive, but it soon became obvious that that wasn't going to work. Maybe the freeze had something to do with it. Anyway, I decided to apply lots of white spirit to the foam while gently pulling the unit away from he lid. This sort of worked, but it really does need more brawn than brain. Eventually, it yielded to my will. Image 13 The adhesive foam was now a soggy mess and couldn't be reused (who'd want to?). I decided to strip away the foam and use something better (remember the double glazing stuff?). Under the foam is the printed circuit board that everyone talks about. Image 14 With the help of an old toothbrush, more white spirit and old old pair of underpants, the black slop was eventually removed from the lamp. Here's what you get. Notice the cracked plastic - too much brawn I guess. Image 15 A dollop of Wilkinson's super glue soon fixed it. The PCB was unaffected. However, many people find that the tracks on this board are corroded so the lamps don't work. The two connecting lugs (feed and earth) are also a weak spot, because they're just rivetted on. Electrical tracks and connectors can be fixed using solder or simply replaced by rewiring the circuits. It's simple enough. Mine were in perfect nick, so I was left wondering why the LEDs went out. It was at this point that I actually examined the LED bulbs. They simply flipped out of the clips! I suppose the constant slamming down of the lid had caused them to come out of the clips. Bad design? Image 16 I took a closer look at them. When I took them out of the lamp, they more or less fell apart. The metal end caps were very slack and were used to nip onto the voltage resistors on each end. The body of the bulb is a plastic tube, not glass. Overall, a pretty cheap affair. Image 17 Worse still, using a 12 volt supply (with correct polarity), they didn't work when I reassembled them. They'd blown/fused/popped or whatever LEDs do. They went in the bin. I found my trusty old festoons in the desk drawer (I never chuck anything away unless it's useless) and decided my LED lighting experience was now complete (long story). With the old bulbs back in place, I now decided to use the sticky mastic to reattach the lamp unit to the lid. The mastic comes in quarter-inch wide rolls with a peel-off backing. Two strips over the PBC would protect it from moisture and hold the unit in place. Here's the 'Flexistrip' mastic going on. EDIT: If you want to use this sticking method rather than a double-sided foam strip, you need Butyl strip/tape available in various widths from eBay. Image 18 The lamp was then offered up to the lid, using a couple of pop rivets as locating pins. These go through the holes on the lid. A small amount of pressure was applied to get complete adhesion. The lamp is actually held by the inner bolts on the plinth, so you just need to ensure the joint is waterproof. I put a thin fillet of mastic across the top edge to ensure this. Image 19 You can now refit the spade connections and test the lamp. My sheared plinth pin was fixed using super glue to locate it, then a reinforcing dollop of Plastic Padding. The plinth goes back on in the reverse order. Before fitting, clean up the rubber seal around the periphery. It collects gunge. I decided to smear the upper seal with silicone sealant just to ensure a water-tight fit.The flange-nuts go on first using the stickum in the socket to prevent accidents. The screwits went on next. I advise being circumspect when fitting these. They will reslacken or shear the pin if overdone. I found that pressing on the plinth allows you to tighten the screwits without unduly stressing the pins. The rubber seal should be snug to the lid end to end. Replace the lid liner by pressing in the fir tree cips. Image 20 Stand back and give yourself a pat on the back. Image 21 TC Disclaimer: You are responsible for any work or modifications carried out on your car and you undertake any such work at your own risk. The 75 and ZT Owners Club nor the original author of these How-To's can be held liable for anything that may happen as a result of you following these How-To's. Any modifications should be reported to your insurance company. Last edited by T-Cut; 29th July 2017 at 09:30.. Reason: Images recovered from the Photobucket ransom. |
16th February 2011, 20:40 | #5 |
Avid contributor
MG ZT 160+ Turbo. MG TF 135 Join Date: May 2008
Location: Livingston
Posts: 169
Thanks: 0
Thanked 0 Times in 0 Posts
|
Wow, fantastic TC
Cheers
__________________
[SIGPIC][/SIGPIC] |
16th February 2011, 22:22 | #6 | |
This is my second home
75 Contemporary SE Mk II 2004 Man. Sal. CDTi 135ps, FBH on red diesel, WinCE6 DD Join Date: May 2010
Location: Leeds
Posts: 17,273
Thanks: 2,160
Thanked 2,061 Times in 1,586 Posts
|
Quote:
That basically means if one LED fails, the rest will get over voltage causing them to fail too. The more fail, the faster the rest will die too.
__________________
Harry How To's and items I offer for free, or just to cover the cost of my expenses... http://www.the75andztclub.co.uk/foru...40#post1764540 Fix a poor handbrake; DIY ABS diagnostic unit; Loan of the spanner needed to change the CDT belts; free OBD diagnostics +MAF; Correct Bosch MAF cheap; DVB-T install in an ex-hi-line system; DD install with a HK amp; FBH servicing. I've taken a vow of poverty. To annoy me, send money. |
|
16th February 2011, 23:52 | #7 |
This is my second home
Rover75 and Mreg Corsa. Join Date: Nov 2006
Location: Sumweer onat mote o'dust (Sagin)
Posts: 21,753
Thanks: 341
Thanked 3,660 Times in 2,924 Posts
|
From my quick glance at the PCB, there were two sets of LEDs wired in series, with a 51ohm resistor on the end of each one. After that I couldn't be bothered figuring it out and dumped them. Had the end caps been standard size, they would be working still. Caveat emptor
TC |
17th February 2011, 12:04 | #8 |
Posted a thing or two
Rover 75 Connie SE Tourer Triumph Street Triple R Join Date: Aug 2009
Location: Bletchley, Milton Keynes
Posts: 1,163
Thanks: 75
Thanked 91 Times in 65 Posts
|
Hey T-Cut, your hard work has proved invaluable to me as I am just in the process of fitting my rear view camera.
I had stripped down all as you had stated without knowledge of your How to and soon discovered that I would need to drill ( Arhhh Shock,,Horror) a hole to receive my camera wire in the boot lid right through the now discovered, well stuck on, PCB.!! Realising this was a hidden from view PCB I hesitated for a minute and then thought, as you do, GTF,,,(Go To Forum!) Well done, I can now drill right through the White plastic, bang on Center and up a little to avoid the two tracks running parallel at the lower edge of the PCB! Good advice on the outer plastic screw it posts, why oh why do they always put a piece of 'dung' somewhere in the a midst of a great item!!!!!
__________________
Real walnut interior. Original refurbished Forked Spokes 16” with Michelin Primacy 4 rubber, Pioneer AVH-Z9200DAB double din Wi Fi phone integration. Retrofitted twin front horns. 160 re-map. Revotec fan. Silicone intercooler hoses and ‘O ring’ replacement. Top hose thermostat. New walnut and smokestone steering wheel with cruise upgrade. Brembo Brakes. Ceramic coated rear Exhaust. L/engine mount, Hydramount, Bosch MAF. Focal Access Drivers and Focal Amp. |
17th February 2011, 12:50 | #9 |
Avid contributor
MG ZT 160+ Turbo. MG TF 135 Join Date: May 2008
Location: Livingston
Posts: 169
Thanks: 0
Thanked 0 Times in 0 Posts
|
All sorted now, cheers Pab and T-cut.
__________________
[SIGPIC][/SIGPIC] |
19th February 2011, 11:55 | #10 |
This is my second home
ZT 260 SE Twilight and 10 other 75 ZT's :O Join Date: Jan 2007
Location: Conwy NORTH WALES
Posts: 11,094
Thanks: 512
Thanked 1,116 Times in 763 Posts
|
Nice job TC
Just found these pics from my archives which might be of help? They show where to solder. 90% of non functioning lamps is like you say down to the rivet joints or corroded PCB tracks which just need bridging with thin wire. Better still run wires the whole length of tracks for good measure.
__________________
[SIGPIC][/SIGPIC] Newbies do now!! 1. Plenum drains..all 3 or 4 year dependent 2. Cooling fan..All speeds functioning 3. Bonnet cable divider block |
|
|