|
||
|
13th April 2017, 19:50 | #1 |
Newbie
Rover 75 Tourer Join Date: Mar 2017
Location: Solihull
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
Clutch pedal straight to floor
Earlier today my clutch went straight to the floor, I managed to lift it back up and pumped it a few times and got some clutch pressure back, but the clutch was very heavy and the bite was just off the floor. I drove back home and while parking the clutch went to the floor again and now the pedal has no pressure and goes straight to the floor every time. I have since tried to check the fluid level and after eventually finding the master cylinder is hidden behind the clutch pedal, I have not been able to access it as I am getting on in years and arthritis means I am not as able bodied as I as in earlier years. I have had a few stupid quotes from various places all of them ridiculous costs. Can anyone please help me find a cost effective solution.
|
13th April 2017, 20:11 | #2 |
Loves to post
Mini Cooper SE Join Date: Mar 2008
Location: Worcester
Posts: 369
Thanks: 39
Thanked 40 Times in 32 Posts
|
Have you seen any evidence of fluid leaking in the footwear or under the car?
I had this issue last year and there was no sign of fluid but the slave cylinder had failed and however much I topped up the master, the pedal kept hitting the floor after a few presses. What age and mileage is the car? Has it had a clutch replaced before? Clutch bleeding info.. http://www.the75andztclub.co.uk/foru...read.php?t=156
__________________
"How can one little insulated wire bring so much happiness?!" Homer J Simpson Last edited by steveharvey2001; 13th April 2017 at 20:16.. |
13th April 2017, 20:20 | #3 |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
There are two things that normally give the symptoms you are having.
1/ The master cylinder at the top of the clutch pedal has failed. 2/ The slave cylinder in the clutch housing has failed. The master cylinder is not too expensive to replace. ( But dear enough. ) The slave cylinder replacement requires the gear box to come off and will cost quite a lot. If this is done it's normal to replace the clutch at the same time as the major cost in the removal of the gear box is the labour charge. There were some forum members prepared to do this work but I'm not sure how you would contact them.--Others on the forum would know this however. Much cheaper than most garages would charge. |
13th April 2017, 20:42 | #4 |
This is my second home
Rover 75 saloon x2, Rover 75 Tourer x2, Rover 220 Coupe Turbo Join Date: Aug 2010
Location: Kirkcaldy, Fife
Posts: 9,036
Thanks: 2,278
Thanked 2,852 Times in 1,718 Posts
|
Clutch time I'm afraid if it's your slave. Make sure you get it done by someone that knows what they're doing. Cost wise - around £500-600. They'll be an expert from the club around your area that will be able to do it.
__________________
Wanted - Indian bride. Cash waiting. (All sorted - bargain) First name and forum name: Ravinder Rover 75 2.0 CDT Connoisseur SE 116 (160 remap) Royal Blue (JFM) This vehicle was the 50,481st 75 to run off the production line, out of 112,381 This vehicle was the 2,238th 75 CDT Connoisseur SE to be made out of 3,775 This vehicle was the 5,002nd 75 in Royal Blue (code: JFM) to be made out of 14,420 Royal Blue 75s |
13th April 2017, 21:15 | #5 |
Loves to post
Mini Cooper SE Join Date: Mar 2008
Location: Worcester
Posts: 369
Thanks: 39
Thanked 40 Times in 32 Posts
|
I had these guys do mine. Was under 400 for the full clutch excluding master.
http://www.a1-clutches.co.uk/ I took mine to Tipton but Birmingham may be more convenient for you.
__________________
"How can one little insulated wire bring so much happiness?!" Homer J Simpson |
13th April 2017, 23:15 | #6 |
Newbie
Rover 75 Tourer Join Date: Mar 2017
Location: Solihull
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
|
The car has done 140000 miles, so presuming it has had a couple of clutches with that mileage, as regarding fluid leaks, i have not seen any evidence either inside or under the car. i was recovered by the AA and the he seemed well convinced that is was the master cylinder that had failed. I on the other hand, would rather find proof, rather than stab in the dark on the first persons say so. Thank you for what you say and I will have to find a way to check the fluid level, before i start spending money on parts.
|
14th April 2017, 08:15 | #7 | |
This is my second home
75 Contemporary SE Mk II 2004 Man. Sal. CDTi 135ps, FBH on red diesel, WinCE6 DD Join Date: May 2010
Location: Leeds
Posts: 17,273
Thanks: 2,160
Thanked 2,061 Times in 1,586 Posts
|
Quote:
Assuming fluid in the MC and the joint parted, if the MC is OK your clutch pedal should be solid/ not press down very far. If it still goes down, then the MC is at fault. If it seems OK, then the slave has failed. Clutch is below the battery, with two hydraulic pipes going down into it. The first the pipe from the MC and the second a short one to allow the system to be bled, which terminates in a bleed nipple.
__________________
Harry How To's and items I offer for free, or just to cover the cost of my expenses... http://www.the75andztclub.co.uk/foru...40#post1764540 Fix a poor handbrake; DIY ABS diagnostic unit; Loan of the spanner needed to change the CDT belts; free OBD diagnostics +MAF; Correct Bosch MAF cheap; DVB-T install in an ex-hi-line system; DD install with a HK amp; FBH servicing. I've taken a vow of poverty. To annoy me, send money. |
|
14th April 2017, 11:28 | #8 | |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Quote:
|
|
12th August 2018, 15:54 | #9 |
This is my second home
Rover 75 Saloon & Tourer Join Date: Sep 2012
Location: Lincoln
Posts: 14,929
Thanks: 1,630
Thanked 3,032 Times in 2,181 Posts
|
welome.
the bell housing may be holding clutch fluid, the master cylinder does not hold very much. DMGRS did at one time offer this service, Andy Willi does it I think at your house, he is a member here. A word of warning, prepared for extra unexpected bills. I have had to replace drop links, low arm bushes and strut bearings as I found all these were duff while doing a clutch job cost effective solution, prove if master cylinder is leaking or a joint in the pipe work. I was going to ask what are your DIY skills like but I see from your original post DIY is not a possibility. DMGRS is a trader here. This is his web site, you can check the cost of parts https://www.dmgrs.co.uk/ good luck macafee2 |
31st May 2022, 07:03 | #10 |
Avid contributor
MG ZT-T Join Date: Aug 2016
Location: larryr123 - Biddenham, Bedfordshire
Posts: 224
Thanks: 27
Thanked 19 Times in 17 Posts
|
Hi Mac,
Thanks for the feedback. I've done quite a few jobs so far on the beast, including rebuilding and refitting the high pressure diesel pump - long job and no knuckles left at the end but satisfying nonetheless. I've also replaced both rear back plates, requiring a fair bit of hacksawing to free up the handbrake cables, but the kits provided by DMGRS were pretty complete and offered an nice complete solution. Also changed rear hubs, with the aid of an angle grinder for ceased inner races, rear coil springs and generally done basic servicing. Never tackled a clutch, but just read up the procedure for changing the master cylinder and if I use the original pipes and the part supplied by DMGRS I should be able to replace that pretty quickly and see if once bled that this does the trick. Your point about separating the self sealing joint under the battery is a good one to determine if the slave is at fault, but given there is a weep from the master cylinder on first inspection, I may as well just get on and change that anyway given the fact it is already on its way out. Fortunately we have another car to bob about in so not in a great rush. Thanks again for all your inputs which are pretty informative. Regards Larry |
|
|