Go Back   The 75 and ZT Owners Club Forums > The 75 and ZT Owners Club Forums > The 75 and ZT Owners Club General Forum
Register FAQ Image Gallery Members List Calendar Mark Forums Read
Notices

Reply
 
Thread Tools Display Modes
Old 14th July 2019, 22:15   #1
T16
I really should get out more.......
 
ZT CDTi 135, ZT260SE

Join Date: Feb 2011
Location: Dundee
Posts: 2,877
Thanks: 10
Thanked 331 Times in 213 Posts
Default Cleaning rad/Intercoolers

Just replacing a condenser on one of the cars, noticed obviously the old rad is pretty dirty (no bent fins though) compared to the fresh new part.

Anyone got any tips for cleaning the fins and getting a bit of the original colour back?

I've seen people recommend silly things like pressure washers etc, that is out, the rad is on the car and I was wondering if there was some sort of wonder chemical that I could lightly spray on and have it take the filth away.

Only thing I can think of right now is spraying some panel wipe into the fins, and using a super soft make up brush.

Wishful thinking really but I wondered if there was some mildly acidic solution out there which might just lift some of the dirt off without causing more harm than good.

Danke.
T16 is offline   Reply With Quote
Old 14th July 2019, 22:29   #2
HarryM1BYT
This is my second home
 
HarryM1BYT's Avatar
 
75 Contemporary SE Mk II 2004 Man. Sal. CDTi 135ps, FBH on red diesel, WinCE6 DD

Join Date: May 2010
Location: Leeds
Posts: 17,273
Thanks: 2,160
Thanked 2,061 Times in 1,586 Posts
Default

Commercial a/c engineers clean down the fins of the outdoor units. It is in a squirty bottle and it cuts through the dirt and grease without damage.



Don't use a pressure washer on the delicate fins, it will wreck them.



__________________
Harry

How To's and items I offer for free, or just to cover the cost of my expenses...

http://www.the75andztclub.co.uk/foru...40#post1764540

Fix a poor handbrake; DIY ABS diagnostic unit; Loan of the spanner needed to change the CDT belts; free OBD diagnostics +MAF; Correct Bosch MAF cheap; DVB-T install in an ex-hi-line system; DD install with a HK amp; FBH servicing.

I've taken a vow of poverty. To annoy me, send money.
HarryM1BYT is offline   Reply With Quote
Old 15th July 2019, 09:05   #3
Tourist
Loves to post
 
2004 Rover 75 Tourer CDTi

Join Date: Apr 2016
Location: Fulbourn, Cambridge
Posts: 454
Thanks: 105
Thanked 123 Times in 101 Posts
Default

In the past I've used engine degreasant, gently stippled onto the radiator with a soft paintbrush on both sides. Once it's worked into the grime, a gentle wash off with a hosepipe will do the job.

As above, don't use anything harsh.

Last edited by Tourist; 15th July 2019 at 09:08..
Tourist is offline   Reply With Quote
Old 15th July 2019, 09:19   #4
T16
I really should get out more.......
 
ZT CDTi 135, ZT260SE

Join Date: Feb 2011
Location: Dundee
Posts: 2,877
Thanks: 10
Thanked 331 Times in 213 Posts
Default

Did it offer an improvement and make it nice and silvery again?

It seems a bit bonkers to replace a rad with a new one so it all looks nice and new, having said that, with the front of the car off, it almost makes some sense to replace the rad after 14 years.

Although if they are made in China, that would not be happening.
T16 is offline   Reply With Quote
Old 15th July 2019, 10:29   #5
bl52krz
This is my second home
 
bl52krz's Avatar
 
Rover 75 cdt club + Rover 2.5 KV6 Conni SE

Join Date: May 2008
Location: Birmingham
Posts: 11,356
Thanks: 6,587
Thanked 2,262 Times in 1,729 Posts
Default

If you do want to re-core your rad/ intercooler, Longford Radiator Services Coventry have a good name.
__________________
Great Barr, Birmingham.
bl52krz is offline   Reply With Quote
Old 15th July 2019, 10:33   #6
Tourist
Loves to post
 
2004 Rover 75 Tourer CDTi

Join Date: Apr 2016
Location: Fulbourn, Cambridge
Posts: 454
Thanks: 105
Thanked 123 Times in 101 Posts
Default

Yeah, it should come back to being shiny as it's alloy and therefore not prone to rusting.

There's no need to replace it if the fins are all fine and it's not leaking - just clean it so that the air can flow through it and flush the inside out in both directions using a hose pipe.
Tourist is offline   Reply With Quote
Old 15th July 2019, 14:16   #7
HarryM1BYT
This is my second home
 
HarryM1BYT's Avatar
 
75 Contemporary SE Mk II 2004 Man. Sal. CDTi 135ps, FBH on red diesel, WinCE6 DD

Join Date: May 2010
Location: Leeds
Posts: 17,273
Thanks: 2,160
Thanked 2,061 Times in 1,586 Posts
Default

Quote:
Originally Posted by Tourist View Post
Yeah, it should come back to being shiny as it's alloy and therefore not prone to rusting.

There's no need to replace it if the fins are all fine and it's not leaking - just clean it so that the air can flow through it and flush the inside out in both directions using a hose pipe.

The atmosphere and road salt attack the alloy and turn them to dust.



__________________
Harry

How To's and items I offer for free, or just to cover the cost of my expenses...

http://www.the75andztclub.co.uk/foru...40#post1764540

Fix a poor handbrake; DIY ABS diagnostic unit; Loan of the spanner needed to change the CDT belts; free OBD diagnostics +MAF; Correct Bosch MAF cheap; DVB-T install in an ex-hi-line system; DD install with a HK amp; FBH servicing.

I've taken a vow of poverty. To annoy me, send money.
HarryM1BYT is offline   Reply With Quote
Old 15th July 2019, 16:01   #8
Tourist
Loves to post
 
2004 Rover 75 Tourer CDTi

Join Date: Apr 2016
Location: Fulbourn, Cambridge
Posts: 454
Thanks: 105
Thanked 123 Times in 101 Posts
Default

Quote:
Originally Posted by HarryM1BYT View Post
The atmosphere and road salt attack the alloy and turn them to dust.
Yeah - very true, but it takes a long time. I recently removed the original items from my 54 plate R75 and if they hadn't been spanged on a truck and bent, they would have been fine for refitting with very little corrosion of the fins.

If the item in question is clearly and visibly knackered then don't bother cleaning it!
Tourist is offline   Reply With Quote
Old 15th July 2019, 16:25   #9
T16
I really should get out more.......
 
ZT CDTi 135, ZT260SE

Join Date: Feb 2011
Location: Dundee
Posts: 2,877
Thanks: 10
Thanked 331 Times in 213 Posts
Default

I ordered some "coil cleaner" as per the advice here.. Two types, a degreasing one, and another alkali one which is "fin friendly" (lol)

Hopefully all good.

Bit of a contrast having a new condenser and a filthy old rad next to each other.
T16 is offline   Reply With Quote
Old 15th July 2019, 16:28   #10
marinabrian
 
marinabrian's Avatar
 
MG ZT

Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
Default

I would be asking myself this.

Does the radiator leak? yes/no if the answer is no then continue to the next question

Does the radiator effectively transfer heat from the engine coolant. yes/no

If you answer yes, then leave it alone, changing a perfectly good component for the sake of changing is not only wasteful, but carries the risk of introducing faults and or inferior components.

You cannot tell me it is vital that the cooling radiator looks the same as the new condenser radiator, it cannot be seen once the car is reassembled

If it's not broken, don't try and fix it

Brian
marinabrian is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 08:55.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright © 2006-2023, The Rover 75 & MG ZT Owners Club Ltd