|
||
|
|
7th June 2008, 07:10 | #1 |
Regular poster
Rover 75 Tourer Join Date: Apr 2008
Location: Beckley
Posts: 54
Thanks: 4
Thanked 11 Times in 5 Posts
|
In-Tank Diesel Fuel Pump (peugeot alternative)
Hi
I've been following the forum threads closely about changing the standard diesel in-tank fuel pump with the peugeot 406 HDI alternative (part number 1525Y3). So I went to my local GSF and said what I wanted to do and gave them the part number (1525Y3). The guys there were helpful and first said that they only did the 1525Z3 which is a Bosch unit, but when they tried the 1525Y3 part number I had on their system it came back as the Siemens VDO and was available for order. So I asked them to order me one. However, what arrived the next day was a pump in a Bosch box with a Bosch label on it and the number 0 986 580 216. The paper inovice that came with it showed the correct part number - 1525Y3. So I'm a little stuck with what to do - Do I take it back and insist it's wrong because it should be a Siemens VDO or can part number 1525Y3 sometimes come as a Bosch unit or perhaps even if they've sent me 1525Z3 by mistake can I still use the pump out of it? A quick response would be great as I think i'd need to take it back asap if it's wrong Many Thanks in advance Keir |
7th June 2008, 07:27 | #2 |
Moderator
MG-ZTT Join Date: Mar 2007
Location: Ware, Herts
Posts: 19,798
Thanks: 161
Thanked 1,249 Times in 1,036 Posts
|
Tricky one this as without putting the 2 pumps side by side, it'll be impossible to judge the differences.
When car manufacturers get parts suppliers to make parts, they should be the same regardles of who made it. I remebr years ago you could get Ford Sierra headlamps made by Bosch, Lucas, Motorcraft and I think Hella. They all fitted and the all worked, but they weren't identical which made them look a bit odd when they weren't matched pairs. I would have thought as long as the connections are the same there shouldn't be an issue, but you may have to suck it and see. The other thought is that the 406 pump may have changed during the life of the model, so is one an early one and the other a later one ? ou could try ringing a Peugeot dealer and get them to check the parts lists to see if the pump did change between models. Good luck.
__________________
David Impecunity is the mother of ingenuity Useful how to's for common problems Car Of The Month Jan 2014 [SatNav Power Down] [Coolant Level] [SatNav Repair] [Diesel Non Starting] [Paint Codes] [Rear Light Seals] [Reversing Light Switch] [Bleeding Brakes][Sunroof Drain] [Early ZT's][Instrument Pack Diagnostics][ATC Diagnostics] |
7th June 2008, 07:58 | #3 |
Regular poster
Rover 75 Tourer Join Date: Apr 2008
Location: Beckley
Posts: 54
Thanks: 4
Thanked 11 Times in 5 Posts
|
Hi
Thanks for the reply David I think it could be ok as the pump itself looks very similar to the one in the 'How to...' guide posted on this forum and as you say it's been over a year since the threads on doing this swap out were posted and so things will have moved on - 1525Z3 seems a natural progression from 1525Y3. I'll remove the pump from my Rover and put them side by side to see if I can judge if it will fit - my only reluctance is that it's sometimes necessary to break the peugeot unit to get the bit I need and so if I do that and it's wrong then I've kind of lost all the savings I was hoping to make by using this pump :lol: Thanks again Keir |
22nd September 2008, 12:36 | #4 |
Newbie
Rover 75 Tourer CDTi manual silver grey year 2002 Join Date: Sep 2008
Location: Flanders
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
|
Hello, I'm new here and am currently doing a intank pump job on my 75 Tourer. I'm trying to find out from what Peugeot 406HDI model exactly the alternate pump is from (year, engine size) as my independent dealer can't locate any Peugeot part on the number 1525Y3. According to him there are three different types of pumps used on a 406 so he won't order unless I can tell him which one exactly it is I'm after. Please help, I need my car tomorrow and would like te get the job done ASAP...
Thanks |
22nd September 2008, 12:59 | #5 |
Loves to post
Rover 75 Saloon Join Date: Nov 2006
Location: Staffs/Derbyshire Border
Posts: 285
Thanks: 19
Thanked 29 Times in 14 Posts
|
The Pug Pump used was from the 306.GSF part No.T18326.See their Website for latest cost.
|
22nd September 2008, 14:27 | #6 |
*
Rover 75 FaceLift Tourer CDTi 170BHP Auto ConnSE 2005 Model Starlight Silver Join Date: Nov 2006
Location: Abergele
Posts: 28,735
Thanks: 0
Thanked 6 Times in 5 Posts
|
Don't know if it is the one you want (I would only ever use the genuine OEM one)
Try here at £197.40 reduced to £98.70 http://www.pugspares.co.uk/PartsSear...ent=Fuel+Pumps |
23rd September 2008, 12:28 | #7 |
Newbie
Rover 75 Tourer CDTi manual silver grey year 2002 Join Date: Sep 2008
Location: Flanders
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
|
Thanks for your replies. Seems the clerck at the Peugeot dealership wasn't too bright as he thought I meant the number mentioned on the pump body itself.
Still, I had to ring over ten Peugeot dealers to finally trace a pump available. I had to take my girfriend's Hyundai Excell to take me there (what a nightmare to drive something like that when you're used to a Rover). Funny detail: the Peugeot garage where I got the pump was right next to a former Rover dealer. Cost was 172 euro's , about 137£ (I'm from Belgium, see) still less half the price of an original Rover-pump. Over here: Rover parts cost shamingly more than in Britain. I've just replaced the pump into the Rover pumpbody and installed it back in the car. Two attempts and she fired up! Jihaa! |
|
|