|
||
|
22nd November 2021, 22:12 | #1 |
Avid contributor
MG ZT-T Join Date: Aug 2016
Location: larryr123 - Biddenham, Bedfordshire
Posts: 224
Thanks: 27
Thanked 19 Times in 17 Posts
|
Airbag warning light
My airbag dash warning light comes on when either the driver of passenger seats are adjusted or go over a bump.
Tried electrical contact cleaner on the contacts under the seats but the problem keeps recurring - any ideas on a permanent fix? |
23rd November 2021, 09:24 | #2 |
I really should get out more.......
Rover 75 connoisseur se v6 auto Join Date: May 2014
Location: Hull
Posts: 2,089
Thanks: 1,842
Thanked 623 Times in 469 Posts
|
1. Sounds like the connectors are loose - i assume beside contact cleaner you have physically pressed the connectors together - if loose you will feel movement as you re-seat them.
2. Are the air bag looms/connectors tie wrapped to the seat itself ?- if so cut the tie wrap - I did this with a re-occurring warning light and it did the trick - every time the seat moves/jolts it loosened the connectors via the tie wrap.
__________________
She came off the Longbridge Line on 20-05-2003 The Silver Machine was the 13th of 160 Rover 75's to come off the production line that day and is the 100th of 527 Starlight Silver Rover 75 2.5 V6 Connoisseur SE Auto saloons listed in the build records produced world wide. |
23rd November 2021, 16:51 | #3 |
Avid contributor
MG ZT-T Join Date: Aug 2016
Location: larryr123 - Biddenham, Bedfordshire
Posts: 224
Thanks: 27
Thanked 19 Times in 17 Posts
|
Hi York, yes I usually give the two under each seat a squeeze and a shake and it usually kills the light on the dash when starting up again.
I'll take a look at the wraps to see if that eases the interference from the seat movement. Regards Larry |
23rd November 2021, 16:54 | #4 |
Regular poster
ZTT 1.8 T Join Date: Aug 2014
Location: Wiltshire
Posts: 31
Thanks: 4
Thanked 5 Times in 4 Posts
|
I've just gone the other way, the blue connectors mount had broken so and I was getting the exact same issue.
I've just cleaned the contacts on both connectors and cable tied the blue back approximately where it should be. Hasn't come back on yet... Looking at the pins in the connector and the length on the connection itself I would say the pins will only make a fraction of the contact inside the sleave that they really should as the male pin is so small it will just bend away from any point of contact over time. It's likely oxidization on the female side that's causing the issue. Maybe try soaking the female side in contact cleaner for a while and if that doesn't do it possibly try very very slight movement on just one of the male pins and then make and remake the connection several times and repeat if necessary.
__________________
Exhaust Bushes Replaced. (Twice ) Fuel Sensor Wires Repaired. F.O.C Fitted. Washer Bottle Pump & Grommet Replaced. (Twice ) HT Leads Replaced. Starter Motor Earth Repaired. Replaced Engine - Liners dropped Air Con Self Service X2 Coil packs Replaced Full Clutch kit. Rear Brake cylinder Replaced Radiator replaced. ODBII Scanner available. Last edited by RhinoTourer; 23rd November 2021 at 22:29.. |
24th November 2021, 21:17 | #5 |
This is my second home
R75 Saloon. Join Date: Feb 2009
Location: France/or Devon.
Posts: 14,003
Thanks: 3,851
Thanked 2,167 Times in 1,816 Posts
|
Quite a few folk ditch the connectors and just solder the wires together. Be difficult to stop them from connecting then.---
|
24th November 2021, 21:36 | #6 | |
This is my second home
ZT260 #243 (resting) Join Date: May 2010
Location: Prestonpans
Posts: 22,610
Thanks: 650
Thanked 4,624 Times in 3,358 Posts
|
Quote:
If you go down that route do it properly, solder, heatshrink and add about 6-8" to all the wiring, that eliminates the possibility of the wiring being affected by seat movement and also allows the wiring to be cut and rejoined should you ever have to remove the seats. Also, by removing the connectors you are shortening what is already tight wiring. |
|
25th November 2021, 00:22 | #7 |
Give to Learn
Freelander 2 Join Date: Aug 2010
Location: West Midlands
Posts: 18,826
Thanks: 1,155
Thanked 6,407 Times in 3,874 Posts
|
Why not change the connectors for some more reliable ones,
1 2 With a little more wire so the seat can be moved without pulling on the connectors
__________________
Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise " |
25th November 2021, 07:39 | #8 |
Avid contributor
MG ZT-T Join Date: Aug 2016
Location: larryr123 - Biddenham, Bedfordshire
Posts: 224
Thanks: 27
Thanked 19 Times in 17 Posts
|
Aren't the connectors forming part of the function of the airbag, and taking them out will render the airbags inoperable in the case of a crash?
The airbag system should work when a MEM (micro electro mechanical) device is triggered when a severe jolt is experienced - are these located in the switches or elsewhere within the actual airbags? |
25th November 2021, 08:06 | #9 | |
This is my second home
ZT260 #243 (resting) Join Date: May 2010
Location: Prestonpans
Posts: 22,610
Thanks: 650
Thanked 4,624 Times in 3,358 Posts
|
Quote:
Last edited by stevestrat; 25th November 2021 at 08:14.. |
|
2nd June 2022, 19:46 | #10 |
Loves to post
Rover 75 Saloon Join Date: Apr 2022
Location: Bolton
Posts: 328
Thanks: 180
Thanked 42 Times in 34 Posts
|
Give it a wiggle!
My car hasn't experienced this phenomena previously, in my <2 months of ownership, however after a journey with my adult (27) granddaughter in the nearside rear passenger seat, I found when I restarted the car, the airbag warning light did not extinguish. Having read previous posts in this thread I investigated the wiring beneath the front nearside seat, and while I could see no obvious break or disconnection, I pressed the connectors, gave the wires a wiggle, and Hey Presto! No Airbag Light on restart.
The granddaughter is going to have to keep her feet from under the seats in future!
__________________
I am Kevin, the car is my Viking shield-maiden, Lagetha! 2000 Rover 75 1.8 Classic SE in Moonstone Green/Black Leather seats and Sandstone Beige Interior (purchased 10 April 2022) 2002 Rover 25 2.0 IL TurboDiesel - gone but not forgotten, you can follow Deric's adventures on YouTube at Boaty's World and Project Nigel. AllegroMan is restoring Deric now. (Owned 25/10/2022-15/05/2023) |
|
|