Maintenance Checks Weekly.
 

Hopefully I am not teaching people to suck eggs so to speak, I thought I would put together in a pictorial how to what I do each weekend to my car.

I normally carry these checks out on a Saturday or Sunday, when I get the time morning or afternoon but always without fail, this gives me piece of mind that the car is ready for the oncoming weeks traveling.

My first port of call it to the local BP or Esso to add petrol and check my tyre pressures.

Set the tyre pressure machine to my PSI which is set out in the MGZT manual 32psi
https://i.imgur.com/syuh4rpl.jpg1

pressurise each wheel in turn including the spare in the boot.
https://i.imgur.com/153dXmBl.jpg2

https://i.imgur.com/6ekPKqnl.jpg3

At the same time check the tyres for splits, cracks, balding or nails all round the car.
https://i.imgur.com/OsXDBf1l.jpg4

Before I left home to sort out the tyre pressures I set the OBD to 19 then 7 to check the temperature and leave the car running while add the pressure.
https://i.imgur.com/EJkUcCPl.jpg5

With the temp up to 100c the fan kicks in the low speed to bring the temp back down, check this through the front grill
https://i.imgur.com/PKGlKh7l.jpg6

Temp moving down nicely as it should if all is well with the thermostat
https://i.imgur.com/GB8oV56l.jpg7a

https://i.imgur.com/MWGuRhLl.jpg7b

My next task is the famous plenums, which i still check each week even if it as been dry just to make sure no debris as entered the lower plenum tube.
https://i.imgur.com/dEc90d4l.jpg8

I start at the OS driver.
https://i.imgur.com/8aDtdAcl.jpg9

Remove the out cover and using a torch check in the plenum chamber
https://i.imgur.com/QUpq0xHl.jpg10

https://i.imgur.com/Wi0JfK2l.jpg11

https://i.imgur.com/l1x1r4bl.jpg12

Next do the NS passenger by removing the outer cover and exposing the spyhole mod if you have it, if not you will have to remove the inner plenum tray.
https://i.imgur.com/qRFzzYOl.jpg13

With the rubber bung removed you can use your plenum rod of your choice, to rod the plenum tube.
https://i.imgur.com/9xYe8Rel.jpg14

https://i.imgur.com/Bc6xFnfl.jpg15a

https://i.imgur.com/WkzsxGIl.jpg15b

Also check the outer wing tubes at the same time.
https://i.imgur.com/O300KnJl.jpg16

https://i.imgur.com/OpKAxNNl.jpg17

Before refitting the driver OS top outer cover, check the brake fluid level top up if needed, if it is down more than the lower level and it was ok last week when you checked it ? then look for leaks in the braking system.
https://i.imgur.com/dusadahl.jpg18

Plenum area sorted now you can move on to the other fluid checks
https://i.imgur.com/PsOzHc6l.jpg19

Washers bottle top up if needed
https://i.imgur.com/9LveRXjl.jpg20

Next power steering fluid remove the cap have a rag ready.
https://i.imgur.com/V1Q0s70l.jpg21

Place the cap on to the rag and give it a wipe.
https://i.imgur.com/hi6H8NLl.jpg22a

https://i.imgur.com/iMWHInCl.jpg23
Reinsert the cap screw it down remove and check the level, once again top up if need be.
https://i.imgur.com/7CJBwUel.jpg24

Next I check the Vis Motors work I am lucky in this respect as I have self testing ones supplied by our own Mr Vis (stocktake) Dave.
https://i.imgur.com/l1O7fWUl.jpg25

https://i.imgur.com/sUbqOY7l.jpg26

To test other wise you need a vis tester, or T4

If you would like the self testing vis motors for your car I am sure Dave (stocktake) would be able to sort you out, drop him a PM.

I now turn my attention to checking all the lights work as they should.
Front lights
https://i.imgur.com/aSMW6Obl.jpg27

Indicators front and side
https://i.imgur.com/IGYFtgHl.jpg28

https://i.imgur.com/whCLJCpl.jpg29

Now check the rear lights, side, brake and indicator lights work.
https://i.imgur.com/chUJFhul.jpg30

You will need someone to press the brake pedal to check the brake lights
Check the number plate lights both work.
https://i.imgur.com/qJ0qPuUl.jpg31

https://i.imgur.com/GD9bst9l.jpg32

Remove the key so you can check the gong alerting you have left the lights on.
https://i.imgur.com/OgGc5N5l.jpg33

Reinsert the key and turn it to position II
https://i.imgur.com/kzXJ9lXl.jpg34

Make sure that the ABS light passes the initial test no air bag lights are on.
https://i.imgur.com/qegdnyOl.jpg35

Set the OBD to section 2.0
https://i.imgur.com/NdyhJEol.jpg36

https://i.imgur.com/k2RSRSFl.jpg37

Press it again to self test the dials etc
https://i.imgur.com/Q6KQlb6l.jpg38

https://i.imgur.com/znyC9pil.jpg39

Check the battery terminals are nice and secure.
https://i.imgur.com/3FaEnEfl.jpg40

https://i.imgur.com/Cimdkz4l.jpg41

https://i.imgur.com/CPOag81l.jpg42

Section 2 oil level checks and water checks, along with the breather pipes etc.
Arctic.

Sectiion Two Checks weekly
 

Section two of the weekly check oil level, coolant water, breather pipes etc.
By now after the drive back home ( 5 miles )and doing the previous checks, the engine will had time to settle to check the oil level.

Remove the dip stick from the oil tube once again have the rag ready.
https://i.imgur.com/ziM8wgbl.jpg42

Wipe the dip stick clean leave it for a few seconds.
https://i.imgur.com/lZYfQ6Rl.jpg43

Remove the coolant cap slowly just in case it is still hot and pressurised, you may hear a hiss if so go slowly.
https://i.imgur.com/Tnclpi4l.jpg44

Check that the coolant O-rings are in good condition and not flat but convex like these are, if you have not already fitted Viton one my advice would be to do so when you can, these are FREE at the Nano meets.
https://i.imgur.com/hyn5Nb0l.jpg45

Make sure the coolant level is just a smidge above the high level 3ml maybe that is how I like it, some like it bang on the level step.
https://i.imgur.com/PiVqs4tl.jpg46

Now back to the oil level as by this time after removing the dip stick a few second/ minutes ago the oil will have been pushed down the tube due to gravity well that my thinking, can not say it is right for sure.
Reinsert the dip stick 25 second count and remove to check the level.
https://i.imgur.com/aH5EbfWl.jpg47

As you can see mine is just above the low level I like it maybe 2ml higher
https://i.imgur.com/tXMpZYVl.jpg48

I will add little oil just enough to bring it up 2ml
https://i.imgur.com/U91XPwUl.jpg49

https://i.imgur.com/dr7zEi8l.jpg50

Topped up cap refitted oil level sorted.
https://i.imgur.com/9UQF4u4l.jpg51a

https://i.imgur.com/H6QtiKNl.jpg51b

https://i.imgur.com/mQHigyYl.jpg51c

My next job is to remove the engine cover two 8m bolts removed with a socket.
https://i.imgur.com/o0A9c9ll.jpg52

Once the engine cover is safely out of the way check all breather pipe joins for security, make sure they are not leaking, or broken if so you will need to sort them out.
https://i.imgur.com/bPThDTPl.jpg53

https://i.imgur.com/AM9cHgJl.jpg54

follow the breather pipes to the ends and check that they are inserted properly, both by the throttle body and into the throttle body.
https://i.imgur.com/jL5qaW2l.jpg55

Also check at the front
https://i.imgur.com/PAiblw1l.jpg56

Even though my temperature is ok and my fan kicks in when it should I always like to check into the V of the engine with a torch for thermostat leaks, as mine was changed just over two years now and still ok.
https://i.imgur.com/MKU18okl.jpg57

https://i.imgur.com/4DxIFEcl.jpg58

https://i.imgur.com/R8xH1wPl.jpg59

https://i.imgur.com/3jVPwKtl.jpg60

Checks finished for this week, if any members check other items in their weekly checks please add to the thread keep motoring.

This is mainly for the V6 engine but the diesel can be checked for fluids etc the same.

Arctic.;)

Jobs that take no time to do and thus saving you money in the long run.

When checking the tyres I also check my full size spare. Plus I make sure the Jack operates as it should.

Nice write up, many thanks.

Excellent thread Steve, I will be using this as a guide from now on.

Thanks

It's an excellent thread with great pictorial.

Just a couple of comments of things that occurred to me while reading.

Firstly it's much simpler to have one of the excellent tyre inflators stored in the boot for most people so that they can check the tyres at home. I also have a quality pressure gauge too.

Secondly the power steering fluid, shouldn't this be checked on a level surface, wheels pointing directly ahead with the engine running?

Not a criticism in any way of your excellent post, more like a question.;)

Excellent guide.
 

Many thanks to Arctic for this clear post. :bowdown:

As above. All fluids should be checked on a level surface. Worth clarifying.

I would add :

- Check tyre treads for stones or debris such as glass. If required turn wheels so that front or rear of tyre is pointing outwards. Remove any debris found, might save a puncture later. Especially if you live in areas with flint stones.

- Visual inspection of brake pad thickness. The rough rule I go by is whatever the thickness seen on the more easily visible side, the other pad could be around half of that.

- Check for coolant leaks - at radiator top hose elbow. All models.

- Check for coolant leaks - diesels only - at thermostat and hose that joins head.

- Inspect belts - petrol models and diesels. Air conditioning belt on the diesels prone to cracking long before the auxiliary belt.

- Check under car for wetness. Maybe oil from engine, coolant leaks or worse (if near brakes) brake fluid.

Cheers

Andrew

Another one of Arctic's brilliant 'How To's :bowdown:

Ever thought of bringing all these together in book form? "The Definitive Guide To 75/ZT Ownership" :D

Thank you guys glad it helps members even though some of it is straight normal practice, hence the statement of hope I not teaching people to sucks eggs :}

Robert yes another good idea which I never thought of at the time make sure your jack and tyre iron and the lock nut remover is in good order ;) at the same time as checking the spare tyre pressure, the spare is most important as it is the one that is going to get you out of trouble should it arise you get a deflated tyre.

Hi Harry.
Excellent points on all you stated above, and a great added addition to the thread which I like :}

I have the tyre inflator and gauge I go to the garage to get the engine up to temp as the V6 oil check after it as been brought up to temp and allowed to settle for about 20 minutes ;) luck as it also my drive is flat.

Hi ....What power steering fluid would you use?

Thanks Keith