|
||
|
||
|
![]() |
#1 |
Posted a thing or two
Rover 75 Saloon Join Date: Apr 2019
Location: Under the car
Posts: 1,840
Thanks: 210
Thanked 244 Times in 221 Posts
|
![]() I'm replacing the front springs & dampers, plus the top mounts & bearings. I was planning on taking the whole lot off in one go, complete with the hub assemblies - as Jules suggests in post 2 here.
According to Rave though (page 47-2) the torque for this nut is 350Nm or 258ft lbs. Is that right? If so, what does everyone use to undo the old nut? And how do you re-torque the new one later on? My torque wrench won't go anywhere near as high as 350Nm. ![]() Pic below borrowed from Jules (link above). ![]() |
![]() |
![]() |
![]() |
#2 |
I really should get out more.......
75 tourer cdti, MG ZS 180, nissan terrano & 1.8t rover 25 Join Date: Feb 2010
Location: Pontefract
Posts: 2,648
Thanks: 17
Thanked 295 Times in 218 Posts
|
![]() Undo by knocking the tab out on the nut and either using an impact gun or a 3 foot bar and jumping on it if required.
Fitting being a reverse. A good pull on a decent breaker bar will provide plenty of torque. All that’s required to torque to 350nm is 35kg on the end on a 1m bar, or 70kg on a 0.5m bar. Then re-tab.
__________________
How to view a car - everything you need to help you inspect a used car VIS motor tester avalible to local members Injector removal tool and auto gearbox pressure tester now available |
![]() |
![]() |
![]() |
#3 |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,648
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
![]() Or treat yourself to a torque wrench capable of 350 Nm!
![]() Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
![]() |
![]() |
![]() |
#4 |
This is my second home
Rover 75 Saloon & Tourer Join Date: Sep 2012
Location: Lincoln
Posts: 15,009
Thanks: 1,630
Thanked 3,032 Times in 2,181 Posts
|
![]() Is there any reason not to switch the offside and nearside hub nuts over?
I think the staking of the nut will be in a different location. I use a torque wrench capable of 350nm to torque them up and an electric impact wrench for undoing them, having unstaked the nut first. Haynes manual also says 350nm macafee2 |
![]() |
![]() |
![]() |
#5 |
I really should get out more.......
MG ZT-T, Rover 75 Tourer Join Date: Mar 2011
Location: Olney
Posts: 2,969
Thanks: 245
Thanked 1,088 Times in 657 Posts
|
![]() |
![]() |
![]() |
![]() |
#6 | |
Posted a thing or two
Rover 75 Saloon Join Date: Apr 2019
Location: Under the car
Posts: 1,840
Thanks: 210
Thanked 244 Times in 221 Posts
|
![]() Quote:
See above ![]() I don't understand what you mean. |
|
![]() |
![]() |
![]() |
#7 | |
Doesn't do things by halves
Rover 75 2.5 Connoisseur Auto (1999) Dealer launch model. Join Date: Mar 2007
Location: Former Middlesex
Posts: 20,648
Thanks: 1,587
Thanked 3,749 Times in 3,181 Posts
|
![]() Quote:
![]() Simon
__________________
"Whatever is rightly done, however humble, is noble." Sir Henry Royce. |
|
![]() |
![]() |
![]() |
#8 | |
Posted a thing or two
Rover 75 Saloon Join Date: Apr 2019
Location: Under the car
Posts: 1,840
Thanks: 210
Thanked 244 Times in 221 Posts
|
![]() Quote:
![]() Norbar's product selector doesn't come up with any 1/2" results ![]() ![]() Last edited by Blink; 4th July 2020 at 13:25.. |
|
![]() |
![]() |
![]() |
#9 | |
same car since 2005
2001 Rover 75 2.0 v6 Connoisseur Saloon Join Date: Nov 2006
Location: Ellesmere Port , Cheshire
Posts: 3,818
Thanks: 379
Thanked 549 Times in 466 Posts
|
![]() Quote:
![]()
__________________
|
|
![]() |
![]() |
![]() |
#10 | |
MG ZT Join Date: Jan 2011
Location: Newcastle Upon Tyne
Posts: 20,151
Thanks: 3,565
Thanked 10,837 Times in 5,718 Posts
|
![]() Quote:
I'm surprised at you Simon Torque wrench HERE Brian ![]() P.S. I use one of these to undo stake nuts, better than a breaker bar any day of the week ; LINK Last edited by marinabrian; 4th July 2020 at 14:28.. Reason: adding link |
|
![]() |
![]() |
![]() |
|
|