|
||
|
||
|
![]() |
#1 |
Newbie
Rover 75 Tourer Join Date: Feb 2014
Location: Shaftesbury, Dorset
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]() Hello everyone,
I would like to start off by thanking everyone for such great forum - so many helpful articles and friendly advice. I have been a member for several years now but embarrassingly I have never posted. However, I am hoping now that someone will be able to help me with the following problem. I while ago, I purchased a replacement hydramount. Last night I removed my old mount and found that the new one is one of those that is larger / taller than the original. There are many mentions of these larger mounts across several threads and some owners seem to have fitted them by cutting down the threads I assume on the top part. On my hydramount, it is the actual body of the mount that is quite a bit taller than the original. So my question is : is this a problem and does it cause any issues with alignment when everything is bolted back up again? Thanks again in advance for any thoughts or comments on this problem. Mark |
![]() |
![]() |
![]() |
#2 | ||
Give to Learn
Freelander 2 Join Date: Aug 2010
Location: West Midlands
Posts: 18,845
Thanks: 1,155
Thanked 6,407 Times in 3,874 Posts
|
![]() Quote:
Where did you get the mount from? is it a Freelander one, the body rubber part is most likely taller because the old one will have compacted over time, how much taller is it. If it is the Freelander 1 mount then yes cut the thread down a little. ![]() ![]() ![]()
__________________
Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise " |
||
![]() |
![]() |
![]() |
#3 |
Newbie
Rover 75 Tourer Join Date: Feb 2014
Location: Shaftesbury, Dorset
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]() Hello Arctic - many thanks for your quick reply.
The new mount came from DMGRS (part number KKB101914) and I believe it is supposed to be correct for the Rover 75. Overall it is 14mm longer - 4mm of that is on the threaded part, 10mm is the rubber body. So - it does sound as though your explanation is correct and it is just that the body of my original mount has compacted. I am going to go ahead on that assumption - fingers crossed. Thank you so much once again, Mark |
![]() |
![]() |
![]() |
#4 | ||
Give to Learn
Freelander 2 Join Date: Aug 2010
Location: West Midlands
Posts: 18,845
Thanks: 1,155
Thanked 6,407 Times in 3,874 Posts
|
![]() Quote:
That should be ok to fit without any alterations, I'm sure matt would have said it they need to be cut down, it was only the Freelander 1 mounts which need trimming ![]()
__________________
Arctic Givology Learn to Give Everything is Achievable ad altiora tendo. Check out our Nano meet dates http://www.midlandsnanomeets.co.uk/ http://www.the75andztclub.co.uk/index.php?thepage=howto " You do the work , we supply the expertise " |
||
![]() |
![]() |
![]() |
#5 |
Newbie
Rover 75 Tourer Join Date: Feb 2014
Location: Shaftesbury, Dorset
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]() Thank you once again Arctic.
That was a surprisingly straightforward job in the end. In fact, most of the jobs I have done on this car have been OK with the helpful articles on this forum. All the best, Mark |
![]() |
![]() |
![]() |
#6 |
Avid contributor
Rover 75 Join Date: May 2015
Location: Leeds
Posts: 135
Thanks: 0
Thanked 17 Times in 11 Posts
|
![]() I suspect that the DMGRS part will be one for a Chinese MG. If you look on the Rimmers site the same part number is listed for the Diesel and 4 cylinder petrol models. Now since MG, to my knowledge, only make a petrol model based on the 75 design. My concern was the part wouldn't be man enough for the diesel engine.
It is why I went with the Freelander TD4 part instead. If the dimensions are off anyway, I would prefer to go with a part designed for a diesel. |
![]() |
![]() |
![]() |
#7 | |
Newbie
Rover 75 Tourer Join Date: Feb 2014
Location: Shaftesbury, Dorset
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#8 |
Regular poster
Rover 75 Saloon Join Date: Apr 2012
Location: London
Posts: 69
Thanks: 1
Thanked 7 Times in 3 Posts
|
![]() Hi Mark,
How did you remove the old part? Regards |
![]() |
![]() |
![]() |
#9 |
Newbie
Rover 75 Tourer Join Date: Feb 2014
Location: Shaftesbury, Dorset
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
![]() Well - I made a rather nice replica of the removal tool from some steel tubing.
I'd like to say it worked brilliantly - but unfortunately the mount was on rather tight and I let the tool slip, which chewed up one of the tabs. That meant I couldn't use the tool anymore so I resorted to the brute force method of a drift and club hammer. That worked really well ![]() Luckily the tool did come in useful when re-fitting because it allowed me to tighten up the new mount to the correct torque. |
![]() |
![]() |
![]() |
|
|